background image

3

© Copyright 2016 Zoeller

®

 Co. All rights reserved.

  1.  Remove all debris from pit before installation.

 

  2.  Use a deep cycle battery only. Refer to battery descrip-

tions on page 6.

  3.  Be sure the pump is on a firm, level surface.

 

 4.  Install a serviceable check valve in the discharge 

line.

 5. Test the unit immediately after installation. Refer to 

STEP 6.

 1.  DO read all installation material with the pump and 

charger.

  2.  DO inspect unit for any visible damage caused by ship-

ping. Contact dealer if unit appears to be damaged.

  3.  DO clean all debris from the pit.

  4.   DO always disconnect pump from power source before 

handling. DO always connect to a separately protected 

and properly grounded ground fault protected circuit. 

DO NOT ever cut, splice or damage power cord. DO 

Ten Helpful Hints For Easy Installation

Do’s  And  Don’t’s  For  Installing  A  Unit

NOT carry or lift pump by its power cord. DO NOT use 

an extension cord with the 

Aquanot

®

. DO NOT lengthen 

battery/pump leads.

  5.  DO install union check valve (see step 3) in the dis-

charge line. DO NOT use

 

a discharge pipe smaller 

than the recommended pump discharge sizes.

  6.  DO test pump immediately after installation to be sure 

that the system is working properly.

  7.  DO review all applicable local and national codes and 

verify that the installation conforms to each of them. 

Performance Characteristics

  6.  The battery  & charger should be placed on a shelf.

  7.  Check float On/Off levels per STEP 2 of instructions.

  8.  Apply grease to the Positive and Negative terminals 

of the battery to prevent corrosion.

  9.  Check the battery water level once a month and add 

distilled water as necessary.

 10. Obtain model number, date code and installation in-

structions before calling factory.

011922

 

Note:

 

Aquanot

®

 

II

 (Model 585) data was developed with the charger supplying DC power to the pump.

TOTAL DYNAMIC HEAD/FLOW

PER MINUTE

EFFLUENT AND DEWATERING

MODEL

Feet

Shut-off Head:

585

Meters

Gal.

Liters

5

1.5

49

186

10

3.0

36

136

15

4.6

25

95

20 ft.(6.1m)

10

GALLONS
LITERS

0

20

0

2

5

5

TO

TAL D

YNAMIC HEAD

4

15

6

20

METERS

FEET

8

25

30

FLOW PER MINUTE

40

60

80

100

20

10

15

25

120

140

160

180

40

35

45

50

200

55

PUMP PERFORMANCE CURVE

MODEL 585

585

Содержание AquaNot 585









Отзывы: