background image

9. 

Remove the cleaner from the pool using the 

handle (refer to Figures 20 and 21). Never lift 

the cleaner out of the pool by the floating cable. 

10.  Loosely coil the cable starting at the cleaner and 

go toward the connection point at control unit. 

Remove any twists along the way. Store the 

cable by wrapping it around the hooks located 

at the rear of the caddy. 

1

2

Figure 20. Remove Cleaner From Pool

3

Figure 21. keep Cleaner vertical to Drain Water 

IMPORTANT

• 

Use your cleaner as often as needed to keep your 

pool clean. 

• 

Clean the filter canister after each cleaning cycle.

• 

Do not leave your cleaner in the pool on a 

permanent basis.

• 

At the end of each cycle, remove the cleaner from 

the pool. Start at the cleaner head and untangle 

any coils in the cable before storing the cleaner.

4.3  Operating the vortex 4 

 CAuTION

To prevent damage to the cleaner, be sure to adhere 

to the following guidelines:

• 

Do NOT remove the cleaner from the pool for 15 

minutes after the cleaning cycle ends. 

• 

Approximately 15 minutes after the cycle is 

completed, the light located on the control unit 

will flash slowly to indicate that the cleaner may 

be removed from the pool. The 15 minute period 

allows the motor to cool and will prevent damage to 

the cleaner.

• 

Remove the cleaner from the pool after the 

cleaning cycle is completed and store on the caddy.

• 

Never lift the cleaner out of the pool by the floating 

cable. Always use the handle to remove it from the 

pool. Refer to Figures 20 and 21.

• 

Remove the cleaner from pool when super 

chlorinating.

• 

Do not handle cleaner while it is in operation.-

NOTE

  Always make sure the cleaner head is fully 

submerged in the water before you begin the 

operation cycle.

When the cleaner is powered ON it will remain in 

standby until one of the cycle program selection buttons 

is pressed. Select either the Cycle I or Cycle II cleaning 

program on the control unit.

Cycle I Program

Cycle II Program

Completed in 1.5hours Completed in 2.5 hours
Maximum coverage in 

minimal time

Intensive and complete 

cleaning

Thorough pool floor 

cleaning

Thorough pool floor and wall 

cleaning

1. 

To start your cleaner, press the desired cycle 

button (Figure 18). "Cycle I" is the most 

commonly selected cleaning program for 

inground pools.

2. 

When the "Cycle I" program button is selected 

the indicator light will illuminate. The cleaner 

will start in a few seconds.

3. 

Depending on the state of your pool it is 

possible to modify the time of the cleaning 

cycle by pressing the   button.  Pressing the 

 button will increase the cleaning time by 

Page

 11 

ENGLISH

  

 

Zodiac

®

 Vortex

 3, Vortex 4 Robotic Pool Cleaner    

|

   Owner's Manual

Содержание Vortex 3





















Отзывы: