manualshive.com logo in svg
background image

Section 3.  Operation 

 CAUTION

To prevent damage to the cleaner, be sure to adhere 

to the following guidelines:

•  Remove the cleaner from the pool after the 

cleaning cycle is completed and store on the caddy 

out of direct sunlight or inclement weather.

•  Take additional care when lifting the cleaner out of 

the pool. It becomes heavier when filled with water.

•  Always remove the cleaner from pool when super 

chlorinating or adding acid.

•  Do not handle cleaner while it is in operation.

IMPORTANT

•  Always make sure the cleaner head is fully 

submerged before you begin operation.

•  Clean the filter canister after each cleaning cycle.

•  Do not leave your cleaner in the pool on a permanent 

basis.

•  At the end of each cycle, remove the cleaner from 

the pool. Start at the cleaner head and untangle any 

coils in the cable before storing the cleaner.

•  Zodiac reccommends only three cleaning cycles per 

week.   

The Zodiac robotic cleaner includes a safety feature 

that automatically stops the cleaner if it is powered on 

but not submerged in water. For pools equipped with a 

beach area, this safety feature is programmed to drive 

the cleaner in reverse and back into the pool when the 

impeller is out of the water.

3.1  Submerging the Cleaner

1. 

Submerge cleaner vertically (1) and hold it 

under the surface, moving gently from side to 

side (2) until the bubbles stop to remove any air 

trapped inside (Figure 3).

2. 

When the bubbles stop, allow the cleaner to 

sink to the bottom of the pool.

3. 

Verify the cleaner is sitting on the bottom  

of the pool. Remove additional air if the cleaner 

is still floating.

1

2

Figure 3.  Submerge and Remove Trapped Air

4. 

Spread the floating cable over the pool, making 

sure there are no kinks or coils in the cable  

(Figure 4). Spread all of the floating cable 

carefully in the pool, ensuring there are no 

kinks or coils.

Figure 4.  Spread Floating Cable Over the Pool

3.2  Running the Cleaner

Begin Cleaning:

 

• 

Press Start/Stop button to begin operation.

Page

 6 

ENGLISH

  

 

Zodiac

®

 FX20 FX30 FX35 Robotic Pool Cleaner   

|

   Owner's Manual

Содержание TX20













Отзывы: