Zodiac Jandy Pro Series JE1500T Скачать руководство пользователя страница 26

Page 24

ENGLISH

  

 

 

Jandy

® 

Pro Series JE Heat Pumps   

|

   Installation and Operation Manual

section 8. troubleshooting

8.1 

troubleshooting Guide

The following table provides symptoms and solutions for general troubleshouting problems for the heat pump.

table 4.  Heat pump troubleshouting Guide

sYMptoM

CorrECtiVE aCtion

Heat pump will not start, no control board display.

Breaker or fuse may be tripped. Reset breaker or check fuse. If 
heat pump still does not run, call for service.

three-phase models only

 - The phases may be 

reversed or there may be a loss of phase, call for service.

Heat pump will not start, control board display working.

Heat pump may be in delay count down of 5 minutes. Make 
sure control board thermostat is calling for heater to come on 
(check setting on thermostat and temperature reading). Make 
sure heat pump is not in cooling mode.

Heat pump runs but does not heat.

Verify cold air is blowing out the top of the heat pump. If the 
heat pump has just been installed or if the pool water has been 
allowed to cool significantly, it is necessary to run the heat 
pump continually for 24-48 hours. If the heat pump has been in 
operation for some time, increase the circulating pump time, or 
switch the control board to Maintain Heat function. If heating a 
spa, verify no air intake stand pipes are open. If heat pump still 
does not heat, call for service.

Heat pump does not run and control board displays:  
FAULT- 
NO FLOW

Verify circulating pump is on and all necessary valves are in the 
correct positions. Verify filter and skimmers are clean. Check 
water level in pool. Temporarily turn off all fountains and water 
falls that bypass the heat pump water inlet. If this does not 
correct the problem, call for service.

Heat pump does not run and control board display shows: 
FAULT- 
HIGH REF PRESSURE

Verify circulating pump is on and that there are no water flow 
restrictions to the heat pump. If the filter pump is a two speed 
or variable speed pump, switch to a higher speed. Make sure 
all necessary valves are open or in the proper positions to allow 
proper water flow to the heat pump. Verify filter and skimmers 
are clean. Check for water level in the pool. This condition may 
also appear if the heat pump has not been operated for an 
extended period. To clear the condition, cycle the heat pump, 
on and off, up to 3 times. If this does not correct the problem, 
call for service.

Heat pump does not run or short cycles and control board 
display shows: 
FAULT- 
LOW REF PRESSURE

Check that fan is operating and air is coming out of the top of 
the heat pump, while short cycling. If heat pump does not run at 
all, call for service.

Heat pump leaking water.

Possible heat exchanger or plumbing leak. Turn the heat 
pump off, then turn circulating pump off for at least one hour 
to see if the water leak stops. If the water leak stops, normal 
condensation is occurring. If the water leak continues, after the 
heat pump is shut off for at least one hour, call for service.

Содержание Jandy Pro Series JE1500T

































Отзывы: