background image

Web Connect Device 

For use with the following Systems: 
AquaLink

®

 RS Systems: Rev R Firmware or later

AquaLink PDA Systems: Rev 6.0 Firmware or later
AquaLink Z4 Systems: All Firmware versions

iAquaLink

 

2.0

H0435500 Rev B

INSTALLATION MANUAL

 WARNING

FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in 

pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist. 

The maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so 

that all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all 

warning notices and instructions that accompany this product. Failure to follow warning notices and instructions 

may result in property damage, personal injury, or death. Improper installation and/or operation will void the warranty.
Improper installation and/or operation can create unwanted electrical hazard which can cause serious injury, property 

damage, or death. 

 ATTENTION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 

device may not cause harmful interference, and (2) this device must accept any interference received, including 

interference that may cause undesired operation. 

NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in 

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio communications.  However, 

there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off and on, the user 

is encouraged to try to correct the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment to an electrical source on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
Modifications made to this equipment, which are not authorized by the manufacturer, may void the user’s authority 

to operate this equipment.

Содержание iAquaLink 2.0

















Отзывы: