Zodiac CYBERNAUT Скачать руководство пользователя страница 5

- Remove the 2 plastic locking clips to take off the bag (diagram 13).  

Empty the bag and clean it under running water or in slightly soapy water if necessary.  
If using soap, rinse thoroughly taking care to turn it over.  Do not wring to dry it, 
or put it in the washing machine.

- Allow to dry away from the robot.

- Also rinse the filter holder plate and remove any debris caught under the flaps.

- Replace the filter bag, with the seam over a small width of the filter holder and the corners

at the corners of the stainless steel rods (Figure 14).
Replace the plastic locking clips.

- Replace the filter holder and click shut.

A D V I C E

• The robot should be cleaned regularly in clean or slightly soapy water, 
but never with any solvent such as trichlorethylene.  Rinse thoroughly.

• Before putting your robot into winter storage, rinse it thoroughly and let it dry in a dry
atmosphere.

• None of the mechanical parts accessible to the user requires greasing.

• Use your robot as often as possible.  This will give you the maximum benefit from a pool
that is always clean and a filter bag that clogs less quickly.

• Part of the pool may occasionally not be absolutely clean after running your robot on 
the automatic program.  If this occurs you can use the manual mode to complete 
the cleaning in very little time.

27

26

Seam

Diagram 13

Diagram 14

Locking clips

3. Cleaning and maintenance

C L E A N I N G   T H E   F I L T E R   B A G

We advise you to clean the filter bag after completion of every cycle.

- Switch off the robot at the mains electricity 

supply and disconnect the control box from the mains.

- Take the robot out of the water using the lifting cord 

(diagram 9). Place the robot upside-down on the ground 
to access the filter holder plate located on the underside 
of the robot, taking care not rest the robot on its floats 
(diagram 10).

- Unlock the four hooks holding the plate (diagram 11).  

Remove it, holding it upside down so that the debris stays in the bag (diagram 12).

Diagram 9

Diagram 10

Diagram 11

Diagram 12

Filter holder plate

Floats

Hooks

Содержание CYBERNAUT









Отзывы: