Zmotion ZMC412 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 59

Zmotion ZMC412 Скачать руководство пользователя страница 38

ZMC412 Motion Controller User Manual V1.5

→

Wiring Note:



The wiring principle of the differential pulse axis interface is shown in the figure

above, and the wiring methods of different types of drivers are different, please

connect carefully.



Please use STP, especially in bad environments, and make sure the shielding layer is

fully grounded.

3.9.2.

Basic Usage Method

(1)

Please follow the above wiring instructions for correct wiring.

(2)

After power on, please use any of the three interfaces ETHERNET, RS232 (default

parameter, it can be connected directly) and RS485 (default parameters, it can be

connected directly, for hardware, adapter is needed) to connect to ZDevelop.

(3)

Set axis parameters, such as, ATYPE, UNITS, SPEED, ACCEL, FWD_IN, REV_IN, etc.

(4)

There are many parameters related to pulse axis, they can be set and checked

through relative instructions, please see “axis parameter and axis status” of “ZBasic”,

or see “ZDevelop/View/Axis parameter”.

«
...
36
37
38
39
40
...
»

Содержание ZMC412




























































Отзывы:

Нет отзывов