Zmotion ZMC412 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 59

Zmotion ZMC412 Скачать руководство пользователя страница 28

ZMC412 Motion Controller User Manual V1.5

Respond time to

close

3μs

80μs

Overcurrent

protection

Support

Support

Isolation method

optoelectronic isolation

Note:



The times in the form are typical based on the resistive load, and may change

when the load circuit changes.



Due to the leak-type output, the shutdown of the output will be obviously

affected by the external load circuit, and the output frequency should not be set

too high in the application.

→

Wiring Reference

→

Wiring Note:

⚫

The wiring principle of high-speed digital outputs OUT (0-3) and low-speed digital

outputs OUT (4-11) are shown in the figure above. The external signal receiving end

can be an optocoupler or a relay or solenoid valve, all can be connected as long as

the input current does not exceed 300mA.

⚫

For the connection of the common terminal, please select the "EGND" port on the

power terminal to connect to the negative pole of the DC power supply of the external

input device. If the DC power supply of the external device and the controller power

supply are in the same power supply system, this connection can also be omitted.

«
...
26
27
28
29
30
...
»

Содержание ZMC412




























































Отзывы:

Нет отзывов