Zmotion ECI0032 Скачать руководство пользователя страница 4

Страница: 4 / 47

◆

Improper installation of the controller may result in misoperation, failure and fire.

Wiring

Danger

◆

The specifications and installation methods of the external wiring of the

equipment shall comply with the requirements of local power distribution

regulations.

◆

When wiring, all external power supplies used by the system should be

disconnected before operation.

◆

When powering on and running after the wiring work is completed, the terminals

attached to the product must be installed.

◆

Cable terminals should be well insulated to ensure that the insulation distance

between cables will not be reduced after the cables are installed on the terminal

block.

Notice

◆

Avoid metal shavings and wire ends falling into the hardware circuit board during

installation.

◆

The cable connection should be carried out correctly on the basis of confirming

the type of the connected interface.

◆

It should be confirmed that the cables pressed into the terminals are in good

contact.

◆

Do not bundle the control wires and communication cables with the main circuit

or power supply wires, etc., and the distance between the wires should be more

than 100 mm, otherwise noise may cause malfunction.

◆

If the controller is not installed properly, it may cause electric shock or equipment

failure or malfunction.

Содержание ECI0032
















































Результаты поиска

Содержание ECI0032

Отзывы:

Похожие инструкции для ECI0032

Бренды по названию

Популярные бренды

Zmotion ECI0032, Руководство пользователя

Результаты поиска

Содержание ECI0032

Отзывы:

Похожие инструкции для ECI0032

Бренды по названию

Популярные бренды