4
6.
Lock
Connection
5.DIP
Switch Settings
1) Switches1-6 are used to set the control panel number in RS485 communication: It is adopted binary coding and
address number should not be repeated in the network.
2) Number 7 switch is used to restore factory defaults: Switch it three times within 10 seconds and restart the device,
3) Number 8 switch is used to set terminal resistance in RS485 communication: Switch it to“ON” status, for adding
4) When electrical lock is connected with access control system, you need to parallel a Fr107
diode (equipped in the
1) The control panel provides lock control output interfaces. For NO lock, it is normal open when power is on, so
2) The control panel supports “dry mode” and “wet mode” by using the jumper. For “wet mode”, short 2-3 and
3) For the Wiegand reader and the InBio reader, the standard power supply is 12V/3A. So we do not recommend
little endian, the address number
these 6 switches are shown in the figure below. Before setting
is set by placing
For example:
Set the
device number as 39 (39=1+2+4+32), the switches status are 111001, that is set number 1, 2,
COM and NO terminals should be used. For NC lock, it is normal
closed when power is on, so COM and NC
package) to prevent the self-inductance EMF affecting the system, do not reverse
the polarities.
a terminal resistance of 120 ohm between 485+ and 485-.
then all data will be cleared and the system restored to factory default setting.
the address, please keep the system powered off. Place the corresponding switches to the desired status,
and the
3 and 6 switches at “ON”.
1
2
4
8
16
32
Restore
Factory Settings
RS485
Terminal
Resistance
EXT
RS485
PC
RS485
STATE
PWR
READER2
READER1
SWITCH
OUT
ACT
1 2 3 4
O
5 6 7 8
N
terminals should be used.
4-5
terminals. The control panel and the lock use separate power supplies: One is connected with +12V and
GND of POWER interface (for the control panel), the other is connected with V+ and V- of LOCK interface
(for the lock). For detailed settings for “dry mode” and “wet mode” ,
please refer to the Installation Guide.
The factory default is dry mode.
3
ACT
D
AUX Input1
E
RS485
Reader
State Indicator
D
Exit Button for
Lock 1
B
Reader for
Lock 1
B
Reader for
Lock 1
PC Network
Interface
Dip switch
RS485
Converter
PC
D
AUX Output1
C
Lock 1
A Lock Power Input
A
Power Input
LINK
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
TAT
E
PWR
R
E
A
D
E
R
2
R
E
A
D
E
R
1
S
W
IT
C
H
O
U
T
ACT
that the lock and the control panel share a common power supply. If it is necessary to do, so we suggest using a
larger one such as 12V/5A.Not including the power reserved, there are 2A current for the lock. For the common
electrical lock (the standby current is 300mA, the max current is 500mA), the maximum connected lock is 4.
AUX Input 1 connect to the infrared human
body induction, wireless exit button, windows
sensor with dry contact (no voltage).
AUX Input 1 connect way is same.
Note:
Output Electrical Parameters:
Rated Voltage: 12V(DC)
Rated Current: 0.5A
1
2
3
4
7
5
6
5
1
AUX Output 1 connect to alarm, door bell and so on;
Port (NO, COM, NC) Electrical Parameters:
MAX Voltage: 36V(DC) MAX Current: 1.25A
Note:
AUX Output 1 connect way is same.
Lock1:
Port (SEN)connect to door sensor single with
dry contact (no voltage);
Port (NO, COM, NC) Electrical Parameters:
MAX Voltage: 36V(DC) MAX Current: 2A
Note:
When you select Wet mode,the power is Lock power,
Lock 1 total load don’t more than Lock power Rated
current (2A).
Lock 1 connect way is same.
2
Lock Power Input Electrical Parameters:
Rated Voltage: 36V(DC) Rated Current: 2A
Device Power Input Electrical Parameters:
Rated Voltage: 12V(DC) Rated Current: 2A
3
4
Exit button for Lock1 connect to Exit button with dry contact.(no voltage);
Reader 1 connect to WG Reader;
Port (+12V)Output Electrical Parameters:
Rated Voltage: 12V(DC) Rated Current: 0.5A
Port (BEEP GLED) Output Electrical Parameters:
Rated Voltage: 5V(DC) Raged Current: 0.5mA
SD Card Interface:
Function:
Backup Access
Control Logs
7
6
7
