background image

BG1000 Series Barrier Gate 

User Manual 

P a g e

 | 2 

 

Copyright©2021 ZKTECO CO., LTD. All rights reserved. 

ZKTeco does not assume responsibility for any errors or omissions in the information or 
documents which are referenced by or linked to this manual. The entire risk as to the results 
and performance obtained from using the information is assumed by the user. 

ZKTeco in no event shall be liable to the user or any third party for any incidental, 
consequential, indirect, special, or exemplary damages, including, without limitation, loss of 
business, loss of profits, business interruption, loss of business information or any pecuniary 
loss, arising out of, in connection with, or relating to the use of the information contained in 
or referenced by this manual, even if ZKTeco has been advised of the possibility of such 
damages.  

This manual and the information contained therein may include technical, other 
inaccuracies or typographical errors. ZKTeco  periodically changes the information herein 
which will be incorporated into new additions/amendments to the manual. ZKTeco reserves 
the right to add, delete, amend or modify the information contained in the manual from 
time to time in the form of circulars, letters, notes, etc. for better operation and safety of the 
machine/unit/equipment. The said additions or amendments are meant for improvement 
/better operations of the machine/unit/equipment and such amendments shall not give any 
right to claim any compensation or damages under any circumstances. 

ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions 
due to any non-compliance of the instructions contained in this manual (ii) in case of 
operation of the machine/unit/equipment beyond the rate limits (iii) in case of operation of 
the machine and equipment in conditions different from the prescribed conditions of the 
manual. 

The product will be updated from time to time without prior notice. The latest operation 
procedures and relevant documents are available o

http://www.

zkteco

.com

If there is any issue related to the product, please contact us. 

ZKTeco Headquarters 

Address

 

ZKTeco Industrial Park, No. 32, Industrial Road,  

Tangxia Town, Dongguan, China. 

Phone 

+86 769 - 82109991 

Fax 

 

+86 755 - 89602394 

For business-related queries, please write to us at 

[email protected]

. 

To know more about our global branches, visit 

www.zkteco.com

 

 

Содержание BG1045L-LED




































Отзывы: