25
water. Wring it out strongly. Let it dry. Drip
some drops of oil onto the filter. Mount the fil-
ter back and fix the cover again.
2.8.5
Cleaning the spark plug
Take off the spark plug cap
26
(Fig. S).
Loosen and remove the spark plug
27
(Fig. T)
carefully. Clean it with a small brush from soot
debris.
The contact distance shall account approx. 0,
5mm or ~ credit card thickness.
2.8.6
Tensioning the chain (Fig. R)
Adjust the chain tension that it isn’t able to
spring out of the guides and that it doesn’t sit
too fast.
Turn the adjusting screw
25
clockwise to ten-
sion the chain and anti-clockwise to loosen it.
2.8.7
Changing the chain
Loosen the nut
32
and remove the cover
33
(Fig. Y).
Loosen the chain.
Remove the chain.
At fitting the new chain you have to take
care that all the guides slide in the
grooves
34
(Fig. Z).
2.8.8
Changing the shears
At first you have to loosen the nuts
35
and
36
(Fig. a).
Now remove the nuts
37
(Fig. b).
Then dismantle the guiding bar
38
(Fig.
c).
Now loosen and remove the screws
39
(Fig. d).
Loosen the socket screws
40
and remove
the cap
41
(Fig. e).
Then you have to disassemble the gasket
42
and the safety cover
43
(Fig. f).
Now lift the connecting rod
44
out of the
cam gear. Take care that you do not lose
the spacer
45
(Fig. g).
Now you can change the shears (Fig. h).
For fitting the new shears you have to do
these steps backwards.
2.8.9
Lubrication
After cleaning you have to lubricate all the
moving parts. Spray the chain with a chain
spray.
Every 15 working hours you must squeeze
some grease into the grease nipples of the
twig saw
31
(Fig. E) and of the hedge trimmer
32
(Fig. G).
2.8.10
Storage
When the machine is stored longer than 30
days:
Drain the fuel out of the fuel tank.
Take off the spark plug and pour some
drops of oil into the cylinder. Turn the en-
gine some times using the cable control so
the oil in the cylinder gets evenly distrib-
uted. Clean the spark plug and fit it again.
Cover the machine and store it at a dry
and clean place.
2.8.11
Controlling the oil level
Before using the twig saw you have to control
the oil level of the oil tank
30
for the twig saw
(Fig. E). Refill it when there’s too less oil in it.
2.8.12
Disposal
Do not dispose your ZI-GPS70
in the residual waste! Contact
your local authorities for infor-
mation about best available dis-
posal possibilities in your area.
Drain fuel from the fuel tank
completely before disposing the machine. Dis-
aggregate the machine into its components
before disposing them.
2.9
Spare part order
With original ZIPPER spare parts you use parts
that are attuned to each other and shorten the
installation time and elongate your machines li-
fespan.
H I N W E I S
The installation of non-original parts renders
warranty null and void.
Exempted is the replacement of the spark plug
if carried out by a specialist.
You find the order address in the preface of this
operation manual.
Содержание ZI-GPS70
