09
807042 v1.00 03.21 HydroTap G5 UltraCare Install Instruct
Installation instructions
Install vent tray kit
(supplied)
Install the vent tray in
the cupboard where
the Command Centre
is located. Refer to
instructions supplied with
the vent tray.
If vent tray is unable to be installed:
Additional ventilation will be required. Options
include vent grilles and a dual exhaust fan kit.
Contact your local service centre for more details.
2.3
93156 Dual Exhaust Fan Kit
2.2
Attach side duct
(supplied)
Insert into the slots in
the side of the HydroTap
Command Centre. Fasten
with a screw.
(18")
40
(1
.5
")
nom.
(
--
")
1 4
5
450
DETAIL: Vent Tray air outlet
cut-out in cabinet
fl
oor
Inlet vent
options
Fit the silicone door buffers to the inside edge of the
cupboard door to provide an air space.
Step 2 – Ventilation
IMPORTANT: Allow a minimum clearance envelope of 50mm either
side, and 200mm above the Command Centre. Proper air circulation
must be provided for the system to operate correctly. The top and front of
the Command Centre must remain accessible for servicing.
2.1
!
4 min.
Buffer Pad
Air Space
SCALE 1:5
SECTION A-A
5
326
m
ax
. 43
60
==
285
450 min.
45
60
mi
n.
284
C. Cabinet Floor Cut-Out
A. Kickboard Cut-Out
B. Cabinet Floor Cut-Out
151
439.5
Ø60
Ø52
85
258
255
5°
226
220
Boiling & Chilled Outlet
Hot & Cold Outlet
Celsius AIO Tap Profile
100 min.
Hot water from
domestic heater
Mains cold water
isolation valve
(not supplied)
Connector
with Strainer
(Feeds Base Unit)
Inlet Vent
A
A
Outlet Vent
240 - 230V,
50Hz GPO
See Detail B
See Detail C
See Detail A
Sink shown
only
Ø50 Hole HydroTap®
Celsius AIO Tap
Position the Tap such that it
dispenses into the sink bowl
with ample clearance for a cup
or a tea pot
440
Celsius Style
All In One Tap
200 m
in.
333
280
50 min.
70 min.
IEC Flex & Plug
Clearance
Envelope
455
THIRD ANGLE
PROJECTION
R
Celsius AIO Tap BC 100/75
Mains Zip HydroTap G4
150
50
200
250
150
100
50
250
200
300
350
400
200
50
100
150
250
200
100
150
Dimensions in
millimetres
Drawing to
BS8888:2004
Screw threads to
BS 8498:2008
Web : www.zipindustries.com
Email : [email protected]
100
400
250
300
350
600
450
500
550
550
650
500
450
600
700
800
750
500
350
400
300
450
550
350
300
450
400
550
500
File Ref : O:\!Design\!SolidWorks\Blocks\Kitchen Layout Blocks\Layouts\BKL002_2824AU0B0ZN1C
Sheet1 ()
Zip Industries Pty Ltd
67 Allingham Street
Condell Park
Sydney
NSW 2200
Australia
Handed? :
Unchecked on 1/01/2001
on
Updated by :
on
00
A1
Created by & on
Created by & on
Potable? :
Recyclable? :
Comments :
Remove all sharp edges. This drawing ONLY details information
which cannot be ascertained from the 3D geometry of the part(s)
attached. Model & dimensions are AFTER all finishing operations
Raw material :
Manufacturing Route :
Make or Buy :
This drawing is CONFIDENTIAL and is supplied on the express condition that it shall not be LOANED, COPIED or DISCLOSED to
any other third party or used for any purpose without the written consent of Zip Industries Pty Ltd. If this document is printed in
hardcopy form, it is for INFORMATION ONLY and therefore not subject to updating controls.
For the current revision ALWAYS refer to the NATIVE electronic form as stated in the top left-hand corner of this sheet.
© copyright Zip Industries Pty Ltd, 17/04/2018
BKL002_2824AU0B0ZN1C
Sheet :
1
of
1
1:1
Unapproved on 1/01/2001
Engineer
on 17/04/2018
Manufacturing Instructions
Zip Industries
Drawing :
Model :
Description :
Status :
Derived from :
Scale :
Approved by :
Checked by :
Finish :
Material :
Mass
(g)
:
Density
(g/cm3)
:
Area
(cm2)
:
Volume
(cm3)
:
Configuration :
Project :
Size
Rev
Colour :
_Drawing
Property
Config
Property
Custom
Property
Outlet vent
450mm cut-out
100mm min
between cut-outs
