background image

04

807042 v1.00 03.21 HydroTap G5 UltraCare Install Instruct

WARNINGS AND PRECAUTIONS

Safety

This appliance is not intended for use by persons (including children) with reduced 
physical, sensory or mental capabilities, or lack of experience and knowledge, unless 
they have been given supervision or instruction concerning use of the appliance by 
a person responsible for their safety. For products sold in Europe, this appliance can 
be used by children aged from 8 years and above and persons with reduced physical, 
sensory or mental capabilities or lack of experience and knowledge if they have been 
given supervision or instruction concerning use of the appliance in a safe way and 
understand the hazards involved. Children should be supervised to ensure that they 
do not play with the appliance. Cleaning and user maintenance shall not be made by 
children without supervision.

Refrigerant

HydroTap chilled models contain R134A refrigerant under pressure. Maintenance 
of the refrigeration unit must be carried out by an accredited service provider or 
qualified refrigeration technician.

Qualifications

If the power cable is damaged it must be replaced by a qualified technician. To 
avoid hazards, all installation procedures must be carried out by a suitably qualified 
tradesperson. 

Venting

Occasionally steam and / or boiling water may discharge through a vent outlet on the 
tap. Ensure the tap body is located so the tap outlet safely dispenses into the drip tray 
or sink bowl area.

Lifting

Take care when lifting. The Command Centre may exceed safe lifting limits. If you feel 
this is beyond your personal capabilities, please seek assistance with the lift. Do not 
lift the Command Centre by the front cover or any of its connections. Refer to the 
technical specification for the weight of the product.

Airflow

The ambient operating temperatures, when installed in a cupboard, must be between 
5°C - 35°C. The system will operate satisfactorily only if the recommended air gaps of 
50 mm on each side, and 200mm above the Command Centre are provided. If a vent 
kit is supplied it must be fitted.

Frost Protection

If this appliance is located where the ambient air temperature could fall below 5°C 
when the heater is not in use, do not turn off the appliance electrically. This safeguard 
does not offer the same protection to the connecting pipework and fittings.

15.  For water taste and quality reasons, following any non-use period of 

more than 72 hours, Zip recommends to perform a system flush. Failure 

to flush the system may affect water quality.

Содержание UltraCare BCU40





















Отзывы: