manualshive.com logo in svg

ZincFive BC Series, Руководство по эксплуатации, Страница: 6 / 30

Поделиться
Скачать
ZincFive BC Series Скачать руководство пользователя страница 6

6  |  Operations Manual

Battery Warnings and Cautions

English

SHIELD EYES AT ALL TIMES WITH PROTECTIVE GEAR.

NO SPARKS. FLAMES. SMOKING.

ALKALINE ELECTROLYTES.

FLUSH EYES IMMEDIATELY WITH WATER.

WET NON-SPILLABLE.

DO NOT INCINERATE PUNCTURE OR IMPACT. 

DO NOT SHORT CIRCUIT.

KEEP OUT OF REACH OF CHILDREN. DO NOT TIP. KEEP LEVEL.

WARNING:

 RISK OF FIRE, EXPLOSION, OR BURNS. DO NOT DISASSEMBLE, HEAT ABOVE 75°C, OR INCINERATE.

French

PROTÉGER LES YEUX EN TOUT TEMPS AVEC UN ÉQUIPEMENT DE PROTECTION.

PAS D’ÉTINCELLES OU DE FLAMMES. INTERDICTION DE FUMER.

ÉLECTROLYTES ALCALINS.

RINCER LES YEUX IMMÉDIATEMENT AVEC DE L’EAU. 

HUMIDE ÉTANCHE.

NE PAS INCINÉRER, PERFORER OU COGNER.

NE PAS COURT-CIRCUITER.

TENIR HORS DE PORTÉE DES ENFANTS. NE PAS RENVERSER. MAINTENIR À NIVEAU.

ATTENTION :

 RISQUE D'INCENDIE, D'EXPLOSION OU DE BRÛLURES. NE PAS DÉMONTER, CHAUFFER AU-DESSUS 

DE 75°C, OU INCINÉRER.

 

Specifications

Refer to the ZincFive BC Series UPS Battery Cabinet data sheet for specifications.
zincfive.com/zincfive-ups-bc-series

Содержание BC Series































Отзывы:

Нет отзывов