ZincFive BC Series Скачать руководство пользователя страница 24

Страница: 24 / 30

24 | Operations Manual

The following information is included in the CSV file for the timespan specified:

and servers will make several data downloads available from the same page. Previous

downloads can be deleted by clicking on the

Delete

link in the

Delete

column.

The following information is included in the CSV file for the timespan specified:

Field Name

Notes

Timestamp

Time stamp of the record.

Battery Voltage 1-38

One column per battery.

Battery Temperature 1-38

One column per battery.

System Temperature

Diode Temperature

Contactor Temperature

State

One of the following:

Service States:

•

Service

•

Pre-Standby

•

Standby

•

Charge

•

Discharge

•

Error

Previous Timestamp State

Previous State

Error Msg

Error Message when in Error State.

Battery System Voltage

Inverter Voltage

Supply Voltage

24 Supply Voltage

System Current

Hall Current

Hall Effect Sensor Current

Shunt Current

SOC

State of Charge

SOH

State of Health

cdah

Cumulative Discharge Amp Hours

adah

Actual Discharge Amp Hours

Firmware Version

Months Sense Commissioning

Elapse Discharge Time

Circuit Breaker Status

ON or OFF

Contactor Control

On or OFF

Circuit Breaker Control

On or OFF

Cumulative Discharge Energy (kWh)

Instant Power (W)

Содержание BC Series



























Результаты поиска

Содержание BC Series

Отзывы:

ZincFive BC Series, Руководство по эксплуатации, Страница: 24 / 30

Результаты поиска

Содержание BC Series

Отзывы: