ZIMO MX31FU Скачать руководство пользователя страница 28

Страница: 28 / 29

Page 28 MX31 Cab, MX31FU Radio Cab

99. Preview

of future software versions

Developments following SW version 1.12

The most important features still missing and improvements to SW version 1.12:

■

Loco and accessory (address) names hand-off’s to other cabs, command station and computer

(the latter for editing and back-up).

■

Reorganization of loco consisting and turnout ladders, among others: usage of names for trains

and turnout ladders.

■

Further simplifications of decoder programming especially for the most often used CV’s such as

characteristic curve and momentum as well as special procedures for ZIMO sound decoders.

■

Special procedures for operating sequences, routes and MX9 operating mode 1.

■

Special procedures for setting up sound decoders.

■

Display and management of booster circuits.

■

Shunting key

The above mentioned points are of first priority; for other plans see chapter 0 (“What’s new?”) in this
manual!

Содержание MX31FU






























Результаты поиска

Содержание MX31FU

Отзывы:

Похожие инструкции для MX31FU

Бренды по названию

Популярные бренды

ZIMO MX31FU, Инструкция по эксплуатации

Результаты поиска

Содержание MX31FU

Отзывы:

Похожие инструкции для MX31FU

Бренды по названию

Популярные бренды