ZIMO MX31, Инструкция по эксплуатации

Страница: 10 / 29

Page 10 MX31 Cab, MX31FU Radio Cab
8. LOCO – mode
OPERATOR
WHEN?
▼
immediately after power-up, if LOCO mode was active before last shut-down, or
▼
activating an address with the F key during address input, or
▼
scrolling through the recall memory using the F key, or
▼
switching from the SWI mode to the LOCO mode with the F key, or
▼
activating an address with the A key from the tabular display of the recall memory, or
▼
activating an address name marked with an “F” from the list of names using the A key, or
▼
after exiting E-procedures, programming and similar with A (Accept) or E (End) key.
From the address input page . . .
with F
with A
From the tabular display . . .
(recall memory, list of names,
see chapter “Recall memory”) . . . to the LOCO mode
CAB?
■
Green display shows:
Top bar: “LOCO”, number of addresses in recall memory and fast clock;
Center: loco address (or name and address), consist indicator “T” where applicable;
Bottom bar: battery and radio signal strength (only with MX31FU in radio
mode), soft key ID’s and applied speed steps (“s…”);
Complete cab (keys, slider, LED’s) is dedicated to the control of the activated
loco.
HOW?
♦
If the LED’s in the light bar next to the display are scrolling up or down , follow
with the slider in the indicated direction until they stop scrolling. This matches the
speed slider to the actual speed of the activated engine. Alternatively move the
slider to zero and press the S key to stop the train.
♦
Control the active engine using all cab elements: speed slider, direction key “R”,
Stop key “ S ”, keys “ MN ” (MAN) and RG (shunting) as well as all number keys
(1 … 0 = F0 … F9) as function keys; corresponding indicators in the
display and with LED’s above each key:
Dir
e
ction key, stop key,
speed slider (with light bar to the left, not visible in this picture)
š
The light bar (6 vertical LED’s next to the display) normally moves
with the speed slider. It also visualizes system controlled acceleration
and deceleration functions, indicates the direction the speed slider
has to be moved to “catch” the speed of an acquired engine and
displays speed limits (red LED’s labeled with L, U, H) provided the
loco decoder sends information back via the bidirectional
communication (= RailCom).
š
The driving direction is switched with the direction key R and indi-
cated in two ways: the usual engine related way with two LED arrows
marked “Fwd” and “Rev”. The arrows also change colors to indicate
active brake and stop functions during change of directions. The
second way to indicate direction is layout related and is shown with
two smaller LED arrows marked “W” and “E” (for West, East). These
indicators are only active if previously set in the LOCO menu or if the
required information is received from the decoder with bidirectional
communication.
š
To stop an active engine immediately, overriding any programmed momentum, use the stop
key S .
New stop and broadcast stop handling from
SW-Version 1.10 !
A broadcast stop that stops all engines on a layout is issued when pressing the -S (shift and
stop key together) or by 3 x S that is, pressing the stop key three or more times within 1 second.
A single stop is indicated with a flashing red LED at the light bar and a flashing “STOP” in the
display, a broadcast stop also with a flashing red LED at the light bar and a flashing “General
Stop” in the display.
Activating the -S again (shift and stop key together) while in a broadcast emergency stop
mode (“General Stop”), turns track power off (“POWER OFF” in display) .
Return to normal operation by pressing the stop key S once from any emergency stop or
“power off” mode as well as from short circuits indicated with “SH-CT MAIN “ or “SH-CT PROG“;
after a 3 second time period has elapsed since stop key was used to initiated emergency stop.
Cha
s
e l
ights move
up (gree
n
) o
r do
wn
Single stop (after pressing
S
) Broadcast stop (after pressing
-S
or
3x S
) Track power off (after
-S
)