INSTALLATION AND OPERATING INSTRUCTIONS:
GPH8000
INSTALLATION AND OPERATING INSTRUCTIONS:
GPH8000
EN / 2021-10-19
EN / 2021-10-19
2 Safety notices
DANGER
Risk of death if not observed
There is a risk of death in the operating range of the product during operation due to a heavy weight and high
gripping forces. When connected to the power supply, there is a risk of injury due to uncontrolled movements of
the product.
►
Never stand within the operating range of the product during operation.
►
Make sure that people cannot get into the operating range of the product during operation.
CAUTION
Risk of injury and material damage in case of non-compliance
Installation, commissioning, maintenance and repairs may only be performed by qualified specialists in
accordance with these installation and operating instructions.
The product is state-of-the-art. It is fitted to industrial machines and is used to hold, transport and store
workpieces.
The following are examples of situations in which the product may cause a hazard:
• The product is not properly installed, used or maintained.
• The product is not used for its designated purpose.
• The locally applicable regulations, laws, directives or guidelines are not observed.
►
The product may only be used in accordance with these installation and operating instructions and the
product's technical data. Any changes or additions to the intended use of the product, as well as modifi
-
cations to the product, such as those in the following examples, require the written permission of the
manufacturer:
•
Use of the product under extreme conditions, such as aggressive fluids or abrasive dusts
• Additional drilled holes or threads
Ö
Zimmer GmbH shall accept no liability for any damage caused by improper use. The operator bears sole
responsibility.
Installation, commissioning, maintenance and repairs may only be performed by qualified specialists in
accordance with these installation and operating instructions.
►
Make sure that the power supply is disconnected before you mount, adjust, modify, maintain or repair the
product.
►
Whenever work is carried out on the product, make sure that the product cannot be actuated by mistake.
►
Perform maintenance tasks, retrofitting or attachment work outside of the machine's danger zone when
possible.
►
Do not reach into the operational range of the product.
►
Observe the specified maintenance intervals and compressed air quality specifications.
►
When using the product under extreme conditions, adjust the maintenance interval according to the degree
of contamination.
3 Proper use
NOTICE
The product is only to be used in its original state with its original accessories, with no unauthorized changes and
within the stipulated parameter limits and operating conditions. Any other or secondary use is deemed improper.
►
Operate the product only in compliance with the associated operating instructions.
►
Operate the product only when it is in a technical condition that corresponds to the guaranteed parameters
and operating conditions.
Ö
Zimmer GmbH shall accept no liability for any damage caused by improper use. The operator bears sole
responsibility.
The product is designed for operation with compressed air only.
The product is designated for use in enclosed rooms for temporary gripping, handling and holding.
The product is not suitable for clamping workpieces during a machining process.
Direct contact with perishable goods/food is not permitted.
4
Personnel qualification
Installation, commissioning and maintenance may only be performed by trained specialists. These persons must have read
and understood the installation and operating instructions in full.
5 Product description
5.1 Type plate
A type plate is attached to the housing of the product.
The article number and the confirmation number are shown on the type
plate.
XXX
XX-XXXXXX
am
an
am
Part number
an
Confirmation number
5.2 Product variants
The product is available in different versions:
• Synchronous without clamp (N-00)
• Synchronous with one clamp (CL-00)
• Asynchronous with two clamps (CL-30)
Zimmer GmbH • Im Salmenkopf 5 •
77866 Rheinau, Germany •
+49 7844 9138 0 • www.zimmer-group.com
Zimmer GmbH • Im Salmenkopf 5 •
77866 Rheinau, Germany •
+49 7844 9138 0 • www.zimmer-group.com
DDOC00289 / b
DDOC00289 / b
4
5
