ZIEHL-ABEGG FXET10AMQ Скачать руководство пользователя страница 33

Страница: 33 / 87

9.2.6

For mode

2.03

Relay output for temperature monitoring

If the set value for the

“

minimum alarm

”

is not reached or the set value for the

“

maximum alarm

”

exceeded, a message is generated via the alarm symbol in the display. In addition,

„

Lmt E1 min

“

displayed alternately with the actual value for the minimum alarm and Lmt E1 max for the

„

Maximum

alarm

“

. An external message follows via the factory-assigned

“

”

relay. (IO Setup: K1 function =

Alarm Minimum

Setting range: OFF / -50...150.0

Factory setting: 0.0

Alarm Maximum

Setting range: OFF / -26.9...150.0

Factory setting: 40.0

Lmt E1 min

Example for display if falling below setting

“

Alarm Minimum

”

alternating to the actual

value display.
Relay

“

”

disengages (if not inverted).

Lmt E1 max.

Example for display if exceeding setting

“

Alarm Maximum

”

alternating to the actual

value display
Relay

“

”

disengages (if not inverted).

Operating Instructions

Fcontrol

–

model series FXET4/6/10AMQ

Programming

L-BAL-E079-GB 1706 Index 008

Part.-No.

33/87

Содержание FXET10AMQ
























































































Результаты поиска

Содержание FXET10AMQ

Отзывы:

ZIEHL-ABEGG FXET10AMQ, Руководство по эксплуатации, Страница: 33 / 87

Результаты поиска

Содержание FXET10AMQ

Отзывы: