ZIEHL-ABEGG Acontrol PDE-6 Скачать руководство пользователя страница 9

The assembly instructions and/or operating instructions are always readily available 
at the location where the device is being used, are complete and are in legible 
condition.

These persons are regularly instructed in all applicable questions regarding occupa-
tional safety and environmental protection and are knowledgeable regarding the 
assembly instructions and/or operating instructions and, especially, are familiar with 
the safety instructions contained therein.

All safety and warning notices attached to the device are never removed and remain 
legible.

2.9 Employment of external personnel

Maintenance and service work are frequently carried out by external employees who 
often do not recognize the speci

c situations and the thus resulting dangers.These 

persons must be comprehensively informed about the hazards in their area of activity.
You must monitor their working methods in order to intervene in good time if necessary.

3 Product overview

3.1 Operational area

The controller described is used for continuous speed adjustment on variable voltage 1~ 
motors used to drive ventilators or pumps.

3.2 Maintenance

The device must be checked for soiling and, if necessary, cleaned in periodic intervals.

3.3 Transport

The device is packed ex factory to suit the transport method previously agreed.

Always use the original packaging materials when transporting the device.

Avoid shocks and impacts to the device during the transport.

During manual handling the human lifting and carrying restrictions must be observed 
and adhered to.

3.4 Storage

The device must be stored in its original packaging in a dry and weather-proof room.

Avoid exposure to extreme heat and cold.

Avoid over-long storage periods (we recommend a maximum of one year).

3.5 Disposal / recycling

Disposal must be carried out professionally and in an environmentally friendly way in 
accordance with the respective national legal stipulations.

"

Separate the materials by type and in an environmentally friendly way.

"

If necessary, commission a specialist company with the waste disposal.

Operating Instructions 

Acontrol

 PDE-6 / PDE-10

Product overview

L-BAL-E048-GB 1921 Index 005

Part.-No. 

9/29

Содержание Acontrol PDE-6






























Отзывы: