background image

TABLE OF CONTENTS 

  Important Safety Information --------------------------------------------------- 2 

  Safety Warnings and Recommendations ----------------------------------- 3 

  Installation --------------------------------------------------------------------------- 5 

  Using Your Heater -----------------------------------------------------------------12 

  Operating Instructions ------------------------------------------------------------14 

  Maintenance ------------------------------------------------------------------------ 17 

  Troubleshooting ------------------------------------------------------------------- 18 

  Technical Specifications --------------------------------------------------------- 20 

  Electrical Diagram ----------------------------------------------------------------- 22 

   

IMPORTANT SAFETY INFORMATION 

PLEASE  READ  THIS  ENTIRE  MANUAL  BEFORE  OPERATING  YOUR  PELLET  HEATER. 

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE. 

1.  Contact  your  local  authority  to  obtain  any  information  on  installation  restrictions  and 

inspection requirements for your area. 

2.  To  prevent  the  possibility  of  a  fire,  ensure  that  the  appliance  is  properly  installed  by 

adhering  to  the  installation  instructions.  The  dealer  will  be  happy  to  assist  you  in 

obtaining  information  with  regards  to  your  local  building  codes  and  installation 

restrictions. 

3.  Be  sure  to  maintain  the  structural  integrity  of  the  home  when  passing  a  vent  through 

walls, ceilings, or roofs. 

4.  The heater’s exhaust system works with negative combustion chamber pressure and a 

slightly  positive chimney pressure. It is very important to ensure that the exhaust system 

is sealed and airtight.   

If you have any questions with regard to your heater or the above-mentioned information, 

please feel free to contact your local dealer for further clarification. 
 

EXCLUSION OF LIABILITY 

Whilst every care has been taken in formulating these instructions, no responsibility whatsoever 

will attach to and/or claim lie against, the manufacturer and/or the distributor of the heater as a 

result  of  any  failure  to  follow  the  whole  or  any  part  of  the  instructions  and/or  as  a  result  of 

incorrect information herein and/or any omission here from. 

 

Содержание KOMFORT



























Отзывы: