Zico QUIC-LIFT LAS-775 Скачать руководство пользователя страница 7

Страница: 7 / 44

B. Electrical System

Now that you are sure of your mounting position, you may begin to lay out your electrical wiring

(pages 22, 29, 37 and 38). At this time, it is a good idea to remove the units from the shelf and "C"

clamp them to a table so that the units will swing out away from the table when lowered. Units should

be mounted the same distance back from edge of table as they would be on the shelf of your apparatus.

Be sure the table is secured by adding a counterweight to the other side before lowering the units. Place

ladders onto the ladder mount castings (item 7, page 15) just as they will be stored on the apparatus.

Determine where wires can be run so they will not be visible from the outside of the apparatus. We

recommend all electrical connections be soldered as this method is superior to crimp connections.

Measure the required run lengths of each wire (see page 22 for proper wire diameter).

Make up a wiring harness using wires longer than the required run lengths. Temporarily make all

wire connections so you can test the system. With the table properly secured, you should be able to

operate the units with the ladders or hard sleeves attached. Be sure the ladders will clear the edge of the

table before drilling any holes in the apparatus. The wiring diagram for the flashing lights may be found

on page 29.

C. Mounting Suggestions

A "WARNING" label (part number 3097-105-149, item 49, page 14) is supplied with each

QUIC-LIFT System. The pressure sensitive label must be mounted by the electrical control switch. All

apparatus operators must be instructed to keep area in front of ladders clear of personnel when the

QUIC-LIFT System is being raised or lowered.

Before starting the installation, you should make sure you have all necessary tools and materials.

This should include matching touch-up paint, edge trim (for cut outs), fender protector cloths and

removable tape (to protect paint), necessary hardware, wire connectors, cable ties, burr remover, vacuum

cleaner (for metal filings), edge guards (for wiring), drills, drill gun, wrenches, step ladders, etc. Be sure

to remove the hose from the hose bed.

Following these simple instructions should make your installation easy and professional.

-7-

Содержание QUIC-LIFT LAS-775













































Результаты поиска

Содержание QUIC-LIFT LAS-775

Отзывы:

Бренды по названию

Популярные бренды

Zico QUIC-LIFT LAS-775, Запчасти и инструкция по эксплуатации

Результаты поиска

Содержание QUIC-LIFT LAS-775

Отзывы:

Бренды по названию

Популярные бренды