Zico QUIC-LIFT LAS-775 Скачать руководство пользователя страница 6

Страница: 6 / 44

INSTALLING THE LADDER ACCESS SYSTEM

A. Preparation for Mounting

Check both units to verify they have matching serial numbers.

Plan and lay out the entire installation before making any cuts or drilling holes in the body of the

fire apparatus. This will keep "out of service" time to a minimum and also help to minimize mistakes.

See Electrical System (Section B, page 7) before any holes are drilled into the apparatus.

Lay the two units on the shelf of the apparatus to that you can see where holes will be required for

the mounting bolts. There should be sufficiently sized flat surface underneath the mounting holes, free

of seams and obstructions where the bolts will pass through. Raise the ladders near the two units to

determine where they will lay when installed. The ladders must be evenly supported by each unit (the

same number of rungs should extend on the outer side of each ladder support).

When the ladder is raised and lowered in this position, it should clear protruding objects on the

apparatus such as emergency lights, hand rails, etc. Make sure that when the ladders are in the up

position they do not obstruct cross lays or hose reels.

Measure the "resting" depth of your ladder combination to determine how far your ladders will

protrude out from the hose bed wall (add depth of 6" for the retracted LAS System). In the event that

the actuator retainer casting (item 48, page 15) or inner arm casting (item 2, page 15) come into contact

with the stiffening rib at the top of the hose bed, you may have to notch out the stiffening rib to recess

the device (see page 21). In the event that the stiffening rib is notched, the exposed metal surfaces

should be painted and covered with an edge guard material. In addition, and in particular, if the

stiffening rib is notched, you may wish to add a backing plate (page 21) on the inside surface of the hose

bed wall. The plate will reinforce the hose bed wall and provide a good mounting support for the

QUIC-LIFT System. The edges should be rounded off, on the side next to the hose, and flat head bolts

should be used to mount the plate.

Bolts 3/8" or larger should be used to mount the base castings to the fire apparatus. When the bases

will only be mounted to the hose bed wall or only mounted to the shelf deck, 1/2" bolts should be used

with substantial backing plates (page 21) and supports. If you are installing the QUIC-LIFT devices to

only one surface, we suggest you contact one of our technicians before beginning.

-6-

Содержание QUIC-LIFT LAS-775













































Результаты поиска

Содержание QUIC-LIFT LAS-775

Отзывы:

Бренды по названию

Популярные бренды

Zico QUIC-LIFT LAS-775, Запчасти и инструкция по эксплуатации

Результаты поиска

Содержание QUIC-LIFT LAS-775

Отзывы:

Бренды по названию

Популярные бренды