30 | GB
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: carbon brushes, grinding wheel, brush
head, sand paper
* not necessarily included in the scope of delivery!
Warning! There are no parts inside the power tool
which can be serviced by the operator! Never open
the power tool! Take it to a qualified specialist for
further maintenance!
10. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer‘s mains connection as well as the
extension cable used must also comply with these
regulations.
Important information
In the event of an overloading the motor will switch it-
self off. After a cool-down period (time varies) the mo
-
tor can be switched back on again.
Damaged electrical connection cable.
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connection
cables with the marking „H05VV-F“.
Ceiling grinding (fig. 11)
For working in ceiling area, fix the grinding head with a
cotter pin (19) (included) as shown in figure 11.
LED light (fig. 10)
To ensure a well lit workplace, use the LED light (4) if
necessary.
Press the switch (20) to switch ON/OFF the LED light
(4).
After use
1.
Switch off the power tool as described, discon
-
nect it from the power supply and Iet it cool down.
2. Clean and maintain the power tool as described
below, and store it carefully.
9. Cleaning, maintenance and repair
WARNING! Unplug the power tool before starting
to work on it (e.g. transport, installation, retrofit
-
ting, cleaning and maintenance)!
Cleaning
a) Keep protective devices, ventilation openings and
motor housings free from dust and dirt as far as
possible.
b) Wipe the power tool with a clean cloth or remove
dust and dirt with compressed air at low pressure
(max. 3 bar).
c) Clean the power tool immediately after each use.
d) Do not use any detergents or solvents as they may
affect the plastic parts of the power tool. Make
sure to avoid any water ingress into the tool.
Maintenance
Check the power tool and accessory parts (e.g. inser-
tion tools) for wear and damage before and after each
operation. lf necessary, replace worn out or damaged
parts with new parts and make sure to comply with the
operating instructions.
Observe any technical requirements.
Grinding plate, brush edge
Have a qualified specialist replace damaged or worn
out grinding plates (9) and brush edges (10) with new
ones of the same type.
Replacing the power supply line
Have a damaged power supply line of this power tool
replaced by the manufacturer or the customer service
or an equally qualified person
in order to avoid risks.
Содержание 935-33
