ZF CruiseCommand 785CE Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 160

background image

ADJUSTMENTS AND TESTS [AT DOCK]

Page 46

7.4 E-2 T

HROTTLE

M

INIMUM

AND

E-3 T

HROTTLE

M

AXIMUM

S

IGNAL

(E

NGINES

S

TOPPED

)

ADJUSTMENTS MAY NOT BE REQUIRED. Verify the existing

Throttle Minimum and Maximum values prior to adjusting them.

Throttle Minimum (E2)

This function allows the installer the ability to adjust the Throttle signal at

Idle, above and beyond the profile set in Select Engine Throttle Profile. This
value is adjustable anywhere between 1% to 97% of the maximum throttle
output capability of the driver. The value must be at least 3% less than Throt-
tle Maximum setting.

Throttle Maximum (E3)

This function allows the installer the ability to adjust the Throttle signal at

full throttle, above and beyond the profile set in Select Engine Throttle Pro-
file. This value is adjustable anywhere between 4% to 100% of the maxi-
mum throttle output capability of the driver. The value must be at least 3%
greater than the Throttle Minimum setting.

Use the Service Field Test Unit and a Multi Meter:

A)Disconnect the Throttle Wire Harness from the Processor.
B) Connect the 8-Pin connector of the Service Field Test Unit to

the Processor Throttle connector and to the Throttle Wire Har-
ness. Refer to Figure 49:

C) Depending on the type of signal required, follow the appropri-

ate column of Table 5:

NOTE: Synchronization is dependent on the Throttle Minimum and Maximum adjustments being

equal on each Processor.

NOTE: Prior to adjustments, the correct Engine Signal Selection should be made as shown in Sec-

tion 6.3.3.

Table 5: Throttle PWM, Voltage, Current Output Adjustments

PWM (Duty Cycle)

Voltage (VDC)

Current (mA)

1) Set Multi Meter to Duty Cycle set-

ting.

1) Set Multi Meter to Voltage setting. 1) Set the Multi Meter up as an Amp

Meter.

2) On the Multi Meter, attach the

Black Lead to COM and the Red

Lead to V.

2)On the Multi Meter, attach the

Black Lead to COM and the Red

Lead to V.

2)On the Multi Meter, attach the

Black Lead to COM and the Red

Lead to mA.

%

V D C

m A

«
...
52
53
54
55
56
...
»

Содержание CruiseCommand 785CE

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CruiseCommand 785CE

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: Opvimus Страницы: 12

Бренд: VMIC Страницы: 126

Бренд: vPipes Страницы: 3

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

Бренд: Keithley Страницы: 71

airPoint Nexus sB3210

Бренд: SmartBridges Страницы: 55

Бренд: NUROTRON Страницы: 16

SmartRack SR42UBEXPKD

Бренд: Tripp Lite Страницы: 8

Бренд: Commax Страницы: 122

Бренд: Akasa Страницы: 2

StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem

Бренд: Compaq Страницы: 112

ST7-EMU3 Series

Бренд: ST Страницы: 39

Бренд: HighPoint Страницы: 3

STEVAL-IHT003V1

Бренд: ST Страницы: 20

Бренд: Exsys Страницы: 16

Dual Window Multi-Graphic Processor MGP 462

Бренд: Extron electronics Страницы: 2

Бренд: Magnescale Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды