background image

STANDARD OPERATING PROCEDURE 
String Inverter Installation – Zeverlution Series 

 

Version 1.2 Effective date 02/08/2017

 

 

Page 3 of 15 

 

INSTALLATION PROCEDURE 

 

String Design Guidelines 

 

To ensure efficient operation and compliance with the regulations, string design options are 
limited. As per AS/NZS 5033 section 2.1.6, PV modules that are in the same string must have the 
same tilt and azimuth angle within a tolerance of ±5°.  
solarcity will determine which layout is most suitable based on a site visit prior to the installation. If 
you find the provided layout to be unsuitable on the day of installation, please contact solarcity 
immediately. The below section should provide a better understanding of our design guidelines. 
As a solarcity installer or contractor, you are expected to report any possible discrepancies with 
the below design guidelines immediately before you proceed with your work.   

 

 

 

For both the Zeverlution 2000s and the Zeverlution 4000 inverters and for arrays with or without 
optimisers the minimum and maximum strings lengths are as follows: 

-

 

minimum

 number of modules per string is 

3

 

-

 

maximum

 number of modules per string is 

10

 

 

5.1.1

 

String Layout Without Optimisers 

Where no optimisers are deployed, modules that are electrically connected as one string need to 
be in the same orientation and tilt. 

5.1.2

 

String Layout with Optimisers 

The deployment of Tigo TS4-R-O optimisers allows modules in a single string to be installed as 
split-arrays with different azimuth and/or tilt angles. As a general guideline, the main or most north 
facing array must have a minimum of 3 modules to reach the inverters start up voltage and won’t 
be optimized – while the “sub-array” will be optimized. Examples of array configurations and the 
correct deployment of optimisers are shown below (with optimized modules shown in blue).  
 

 

5.1.3

 

Shading 

 

The benefit of optimisers in partially shaded arrays is insignificant. For solarZero systems, in some 
instances, shading is mitigated by installing one additional module. solarcity will determine if this 
is a suitable solution on a case by case basis. 
 

 

Содержание Zeverlution 2000S

















Отзывы: