Zero FXS 2019 Скачать руководство пользователя

Страница: 99 / 158

General Maintenance

6.25

7. Unhook the headlight bulb spring clip (E) by pushing

down and to the side.

8. Lift up on the spring clip and remove the headlight bulb.

CAUTION:

Do not touch the glass portion of the headlight

bulb. Keep the headlight bulb free of contaminants. Oil
from your fingers or contaminants will shorten the life of
the bulb. Thoroughly clean any fingerprints or
contaminants from the bulb using a clean cloth moistened
with alcohol.

9. Install the replacement headlight bulb into the lens.

10.Installation is the reverse of the removal procedure.

Turn Signal Light Bulb Replacement

1. Remove the turn signal lens screw (A) and remove the

lens.

2. Push in on the bulb, turn the bulb counterclockwise,

and then pull the bulb out.

3. Insert the new bulb into the socket, push in and turn

clockwise until it stops.

4. Install the lens and screw; tighten the screw. Do not

over-tighten the screw.

Zero Owner's Manual (FX and FXS).book Page 25 Tuesday, October 23, 2018 1:54 PM

Содержание FXS 2019































































































































































Результаты поиска

Содержание FXS 2019

Отзывы:

Похожие инструкции для FXS 2019

Бренды по названию

Популярные бренды

Zero FXS 2019, Руководство пользователя

Результаты поиска

Содержание FXS 2019

Отзывы:

Похожие инструкции для FXS 2019

Бренды по названию

Популярные бренды