manualshive.com logo in svg

Zero FXS 2019, Руководство пользователя

Поделиться
Скачать
Zero FXS 2019 Скачать руководство пользователя страница 100

General Maintenance

6.26

Brake/Tail Light Bulb Replacement

To replace the brake/trail light bulb:

1. Remove the brake/tail light lens screws (A) and remove 

the lens.

2. Push in on the bulb and turn the bulb counter-clockwise 

then pull the bulb out.

3. Insert the new bulb into the socket, push in and turn 

clockwise until it stops.

4. Install the brake/tail light lens and screws; tighten the 

screws. Do not over-tighten the screws.

Running Light Bulb Replacement

1. Remove the two bolts (A) securing the trim cover above 

headlight assembly to the motorcycle.

2. Release and remove the trim cover.

3. Remove the four bolts (B) securing the headlight 

assembly to the headlight assembly retaining brackets.

4. Release the headlight assembly.

Zero Owner's Manual (FX and FXS).book  Page 26  Tuesday, October 23, 2018  1:54 PM

Содержание FXS 2019































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды