Zero FX 2018 Скачать руководство пользователя страница 91

Страница: 91 / 156

General Maintenance

6.19

7. Rotate the rear wheel a quarter-turn and repeat the

frequency measurement.

8. Compare your belt’s frequency readings to the

recommended range values below.

9. Adjust drive belt tension if the frequency is outside the

recommended range.

Drive Belt Adjustment Procedure

Note: Adjust both sides (left and right) equally.

1. Remove key from the key switch.

2. Loosen the rear axle nut (C) on right side of motorcycle.

3. Loosen the (left and right) 13 mm jam nuts (A).

4. Turn the (left and right) 13 mm adjustment bolts (B) 1/4

turn at a time until the belt adjustment is within
specification.

5. Tighten left and right jam nuts (A) to secure the belt.

6. Tighten the axle nut (C) on right side of motorcycle.

Torque 75 lb·ft (102 Nm).

7. Test ride the motorcycle.

8. Recheck the belt for proper adjustment after the test

ride and readjust, if necessary.

Belt Pitch

Recommended Frequency Range

11 mm

42.5 Hz to 73.6 Hz

Zero Owner's Manual (FX and FXS).book Page 19 Monday, September 11, 2017 10:13 AM

Содержание FX 2018





























































































































































Результаты поиска

Содержание FX 2018

Отзывы:

Бренды по названию

Популярные бренды

Zero FX 2018, Руководство пользователя

Результаты поиска

Содержание FX 2018

Отзывы:

Бренды по названию

Популярные бренды