manualshive.com logo in svg

Zero FX 2018, Руководство пользователя

Поделиться
Скачать
Zero FX 2018 Скачать руководство пользователя страница 53

General Operation

4.11

Spring Preload Adjustment

The spring preload is adjusted by turning the 19 mm 
anodized hex nut (B) located on top of the fork spring.

Note: When adjusting preload, always start from the 
minimum setting and adjust each fork leg evenly.

•

Turning the adjustment nut clockwise increases the 
spring preload and reduces sag of the front 
suspension.

•

Turning the adjustment nut counter-clockwise 
decreases the spring preload and increases sag of the 
front suspension.

Rebound Damping

The rebound damping is adjusted by turning the slotted 
adjuster screw (A) on the top of both fork legs. Next to the 
screw are the letters “H” meaning 

Hard

 (

MAX

, which is for 

slower rebound) and “S” meaning 

Soft

 (

MIN

, which is for 

faster rebound). This determines how quick the fork 
returns to its extended position after being compressed.

•

Turning the rebound adjuster screw clockwise slows 
the rebound speed down making it better for larger 
rolling terrain or bumps.

•

Turning the rebound adjuster screw counter-clockwise 
increases the rebound speed making it better for 
smaller more frequent bumps. Adjust each fork leg 
equally.

CAUTION:

 Adjusters should never be forced completely 

“Soft” or “Hard”; always leave one click of adjustment in 
either direction.

Zero Owner's Manual (FX and FXS).book  Page 11  Monday, September 11, 2017  10:13 AM

Содержание FX 2018





























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды