Zero FX 2015 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 136

background image

General Operation

4.15

Quick Charger LED Indicators

A.

Ammeter

The Ammeter LED is an amber indicator that indicates
the amount of current output and should gradually
ramp down from “IIIIII” to “I”.

B.

80% Charge

The 80% Charge LED is an amber indicator. If it is on
solid, the bulk charge phase is complete, 80%
charged. Charger is now in absorption phase. If the
indicator is flashing, there are two issues that can
cause this to occur:

•

The charger and BMS are balancing.

•

The BMS is cutting off the charge because one or
more cells have reached maximum voltage.

C.

100% Charge

The 100% Charge LED is a green indicator. If it is on
solid, the charging is complete and the off-board
accessory charger will enter maintenance mode. If it is
flashing, the absorption phase is complete and the
charger is in finish phase.

D.

AC ON

The AC ON LED is an amber indicator. If it is on solid,
the AC power is good. If it is flashing, the AC voltage
is low. Check for proper voltage, and if an extension
cord is being used, verify that it is the correct length.
Maximum length is 25 ft. (7.6 m) 12 AWG.

E.

Fault

The Fault LED is a red indicator which indicates there
is a charger error. If it is flashing, reset the charger
and see

“Troubleshooting”, on page 6.1

.

Zero Owner's Manual (FX).book Page 15 Thursday, April 5, 2018 1:40 PM

«
...
57
58
59
60
61
...
»

Содержание FX 2015









































































































































Отзывы:

Нет отзывов

Похожие инструкции для FX 2015

Бренд: GAS GAS Страницы: 56

Бренд: Öhlins Страницы: 8

Бренд: KEEWAY Страницы: 164

Бренд: hepco & becker Страницы: 6

Бренд: X-lite Страницы: 76

Бренд: kellermann Страницы: 2

Бренд: R&G Страницы: 8

Бренд: GYS Страницы: 36

Windscreen N20012A

Бренд: VStreamT Страницы: 3

Easyrack 661658 01 01

Бренд: hepco & becker Страницы: 4

Бренд: Bajaj Страницы: 319

Бренд: BMW Страницы: 160

R 1200 RT - 2006

Бренд: BMW Страницы: 194

Бренд: BMW Страницы: 223

Бренд: BMW Страницы: 169

Бренд: BMW Страницы: 133

Бренд: BMW Страницы: 8

Бренд: BMW Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды