Zero DS 2012 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 120

background image

4-10

Charging The Power Pack

WARNING:

Charge the Zero power pack with the Zero

charger.

It is possible for lithium ion cells to overheat and fail.

It is recommended to charge in a location that is
away from combustible materials and in a well-
ventilated area. If charging your Zero motorcycle
outdoors, avoid charging in the rain.

The maximum power pack internal charging
temperature is 52°C (125°F). If the power pack’s
internal temperature is over 52°C (125°F), it will not
accept a charge until it is moved to a cooler location.
Also, if the power pack has just been run hard, it may
internally be above 52°C (125°F) even if the ambient
temperature is lower.

C. 100% Charge
The 100% Charge LED is a green indicator. If it is on
solid, the charging is complete and the charger will
enter maintenance mode. If it is flashing, the
absorption phase is complete and the charger is in
finish phase.

D. AC ON
The AC ON LED is an amber indicator. If it is on
solid, the AC power is good. If it is flashing, the AC
voltage is low. Check for proper voltage, and if an
extension cord is being used, verify that it is of the
correct length. Maximum length is 7.6 m (25 ft.)
12-AWG.

E. Fault
The Fault LED is a red indicator which indicates
there is a charger error. If it is flashing, reset the
charger and see section 6, Troubleshooting.

«
...
45
46
47
48
49
...
»

Содержание DS 2012

























































































































Отзывы:

Нет отзывов

Похожие инструкции для DS 2012

Бренд: Suzuki Страницы: 230

Бренд: Cobra Страницы: 38

Бренд: MOTO GUZZI Страницы: 266

Бренд: Megelli Страницы: 83

Бренд: A.J.S. Страницы: 94

Бренд: Yamaha Страницы: 287

Бренд: Yamaha Страницы: 109

Бренд: hepco & becker Страницы: 2

Бренд: Dynafit Страницы: 20

Бренд: Bosch Страницы: 160

Бренд: Ops-Core Страницы: 20

Бренд: Norton Страницы: 69

BLITZ 9-13 Visor

Бренд: Fubag Страницы: 17

Krauser 610.092 00 02

Бренд: Wunderlich Страницы: 4

Бренд: Pacific Helmets Страницы: 48

Prime R1-HD2-9813

Бренд: Rockford Fosgate Страницы: 18

Бренд: cleanAIR Страницы: 146

Бренд: ArcOne Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды