Zero B eco smart, Руководство пользователя

Страница: 12 / 19


Connect the permeate line as per the application.

Check the functioning of the unit before actual usage of the unit.

Before inserting the 3 – pin plug of the system into the main socket ensure correct
voltage and proper earthing of the mains line.

Open the inlet water line and check for line pressure. After checking connect the
inlet line.

Insert 3 – pin plug in the socket. Switch
ON
the mains.

Unit will come ON indicating Power ON and Process ON ( with sufficient
water pressure and user tank empty)

Disconnect the outlet line going to user line like storage tank, cooler etc. so that the
water coming out for first 10 – 15 minutes is drained out.

AFT Check:
Observe for a flow on the reject line. Switch OFF the unit and switch it
ON. This will start the flushing cycle for 15 seconds after every 15 mins of process.

Measure the permeate flow coming from the disconnected permeate line.

Connect the permeate line to the user line, which is most likely to have a tank with
float valve or tap connection.

Check for Tank Level Control
:
A. Start the system once again, if the tank is empty or product water tap is open, then
the PROCESS ON (pump) indication will be seen on the digital monitor.
B. When tank is full or on closing the product water tap, the system will shut down with
TANK FULL (full)
indication on digital monitor
Check for NO WATER : When tank is empty or product water tap is open, system will restart.
Gradually close the inlet water tap to a point when there is no water or very little
flow. System will shut down showing a NO WATER (waterlack ) Indications.
Check for TDS: Check the TDS of the permeate water with TDS indicated on the digital panel
NOTE: A Flush symbol will be seen for 90 seconds only during POWER ON
( when switching ON the unit ) This is an internal loop flushing not seen outside)
NOTE: When system pressure exceeds 9 kg/sq cm, unit will shut off.
To reset the system, please Switch off MCB and Switch ON the unit once
again or Zero B Customer Care No. 022 6618 1234 / hws.service@ionexchange.co.in
How to check the functions ?

Connect the permeate line as per the application.

Check the functioning of the unit before actual usage of the unit.

Before inserting the 3 – pin plug of the system into the main socket ensure correct
voltage and proper earthing of the mains line.

Open the inlet water line and check for line pressure. After checking connect the
inlet line.

Insert 3 – pin plug in the socket. Switch
ON
the mains.

Unit will come ON indicating Power ON and Process ON ( with sufficient
water pressure and user tank empty)

Disconnect the outlet line going to user line like storage tank, cooler etc. so that the
water coming out for first 10 – 15 minutes is drained out.

AFT Check:
Observe for a flow on the reject line. Switch OFF the unit and switch it
ON. This will start the flushing cycle for 15 seconds after every 15 mins of process.

Measure the permeate flow coming from the disconnected permeate line.

Connect the permeate line to the user line, which is most likely to have a tank with
float valve or tap connection.

Check for Tank Level Control
:
A. Start the system once again, if the tank is empty or product water tap is open, then
the PROCESS ON (pump) indication will be seen on the digital monitor.
B. When tank is full or on closing the product water tap, the system will shut down with
TANK FULL (full)
indication on digital monitor
Check for NO WATER : When tank is empty or product water tap is open, system will restart.
Gradually close the inlet water tap to a point when there is no water or very little
flow. System will shut down showing a NO WATER (waterlack ) Indications.
Check for TDS: Check the TDS of the permeate water with TDS indicated on the digital panel
NOTE: A Flush symbol will be seen for 90 seconds only during POWER ON
( when switching ON the unit ) This is an internal loop flushing not seen outside)
NOTE: When system pressure exceeds 9 kg/sq cm, unit will shut off.
To reset the system, please Switch off MCB and Switch ON the unit once
again or Zero B Customer Care No. 022 6618 1234 / hws.service@ionexchange.co.in