background image

Page3 

 

 

GAS CONNECTION:

 

 

The  appliance  inlet  is  to  the  8mm  plain  straight  tube,  allowing  connection  by 

means  of  a  gas-tight  compression  fitting  to  comply  with  both  EC  and  local 
regulations.  The  freezer  is  suitable  for  connection  to  butane/propane  mixtures 
(LPG)  at  2.8-3.0  kPa  and  to  propane  at  3.7  kPa.  Means  must  be  provided  to  turn 
off the gas supply. If the supply is common to other appliances a separate tap must 
be fitted for the freezer line. 

WARNING

:

ENSURE  THAT  THE  GAS  SUPPLY  HOSE  IS  NOT  IN 

CONTACT WITH OR NEAR THE BURNER BOX

 

 

GAS-PRESSURE REGULATOR

 

 

This appliance requires an operating pressure of 2.8 kPa at the appliance. A 
suitable LPG regulator that complies with the requirements of SANS 1237 
must be installed. 

 

OPERATING INSTRUCTIONS FOR FREEZER

 

 

It  is important to read through these instructions carefully before beginning to use 
this appliance. 
Retain these instructions for future reference. 

 

LP. GAS OPERATION:

 

 

After  initial  installation,  after  changing  gas  cylinder,  after  servicing,  etc.,  the  gas 
pipes may contain some air, which should be allowed to escape by briefly pressing 
on the safety valve knob (A).  This will ensure that the flame lights quickly. 
Do not press knob A for more than 15 seconds 

– see Users note. 

 

BURN-BACK (FIRE IN BURNER TUBE OR CHAMBER) 
(REFER PAGE 4 

– TO START GAS OPERATION)

 

In the event of a burn-back, where the flame burns back to the jet, immediately turn 
off the gas supply at the control valve on the gas bottle or gas supply . After 
ensuring the flame is extinguished, re-open and re-light the appliance in the normal 
manner. Should the appliance again burn back, close the control valve and call a 
service technician. Do not use the appliance again until the service technician has 
declared that it is safe to do so. 

 

WARNING

 

This  appliance  consumes  air  (oxygen).  Provide  ample  ventilation  especially  when 
sleeping.  To  avoid  endangering  your  life  do  not  use  this  freezer  in  unventilated 
structures.   Provide additional ventilation for any additional fuel burning appliances 
and  additional  occupants.      Always  ensure  nothing  is  covering  or  blocking  the 
flue(chimney). 

 

FOR YOUR SAFETY

 

 

If you smell gas:

 

 

1.     Turn off gas supply at bottle. 
2.     Extinguish all naked flames 
3.     Do not operate any electrical appliances. 
4.     Ventilate the area. 
5.     Do not smoke while checking for leaks. 
6.     Do not check for leaks with an open flame. 

Содержание GEV60













Отзывы: