Zepro ZHZ 500 Скачать руководство пользователя страница 5

Страница: 5 / 44

Important information

www.zepro.com

ZHZ 500/600-850

Important information

1.1

Attention!

The following warning signs appear in the installation instructions and are intended to draw your attention to cir-

cumstances that can potentially cause problems, near misses, personal injury and/or damage to the product, etc.

WARNING!

WARNING indicates a potential hazard, which if ignored may lead to serious, life-threatening injury.

CAUTION!

CAUTION indicates a potential hazard, which if ignored, may lead to minor injuries.

IMPORTANT

IMPORTANT indicates a risk of equipment damage.

NOTE!

NOTE! refers to additional information that may help the reader understand, or perform, a given operation.

1.2

Technical support

If technical support is needed, please contact ZEPRO. Tel: +46 (0)10-459 05 04, E-mail: [email protected].
Always be ready to state the tail lift’s production number to guarantee you receive the correct information.

The production number is given on the identification plate located on the tail lift frame.

Fig 1. Identification plate

Содержание ZHZ 500













































Результаты поиска

Содержание ZHZ 500

Отзывы:

Похожие инструкции для ZHZ 500

Бренды по названию

Популярные бренды

Zepro ZHZ 500, Инструкция по установке

Результаты поиска

Содержание ZHZ 500

Отзывы:

Похожие инструкции для ZHZ 500

Бренды по названию

Популярные бренды