Zephyr ALA-M90BBX Скачать руководство пользователя страница 9

Страница: 9 / 14

- 22 -

INSTALL THE HOOD

Remove the plastic protective film from all
exterior surfaces, duct covers and filters, prior
to final installation

1. Construct wood wall framing that is flush with

interior surface of wall studs (Fig.22/23).

Make sure:
a) the framing is centered over installation

location.

b) the height of the framing will allow the hood to

be secured to the framing within the
dimensions shown.

2. Determine desired height over cook top

and mark hood bottom line. Install drywall
anchors and 4,8x38mm screws per
dimensions shown in Fig. 22/23.

3. Hang the hood onto the screws.
4. Tighten mounting screws. Add additional

screws through hood body as needed for
additional support.

Notes:

a. Minimum hood distance above cook top

must not be less than 24”. A maximum of
36” above cook top is highly
recommended for best capture of cooking
impurities. Distances over 36” are at the
installer and the users discretion; and if
ceiling height and flue lenght permit.

FRAMING BEHIND WOOD

CROSS SUPPORT

WOOD CROSS

SUPPORT BEHIND

DRYWALL

8-1/4”

16-7/16” FROM

BOTTOM OF HOOD

HOOD

BOTTOM

FIG.22

FRAMING BEHIND WOOD

CROSS SUPPORT

WOOD CROSS

SUPPORT BEHIND

DRYWALL

FIG.23

Model Layers

8-1/4”

15-11/16” FROM

BOTTOM OF HOOD

HOOD

BOTTOM

Model Duo

Содержание ALA-M90BBX















Результаты поиска

Содержание ALA-M90BBX

Отзывы:

Похожие инструкции для ALA-M90BBX

Бренды по названию

Популярные бренды

Zephyr ALA-M90BBX, Инструкции по установке и использованию, предупреждения

Результаты поиска

Содержание ALA-M90BBX

Отзывы:

Похожие инструкции для ALA-M90BBX

Бренды по названию

Популярные бренды