Zenoah GZ2700T Скачать руководство пользователя страница 20

Страница: 20 / 84

Basic adjustments and run-in

The basic carburetor adjustments are done at the

factory. The basic adjustments are high speed needle

(H) = 2 ½ turns and low speed needle (L) = 2 turns.
To give the components of the engine sufficient

lubrication during run-in, adjust the idle speed. Adjust

the idle speed to 600-700 rpm below the recommended

maximum idle speed.

CAUTION: If the saw chain rotates at idle

speed, turn the idle speed screw

counterclockwise until the saw chain stops.

To adjust the low speed needle (L)

1. Turn the low speed needle clockwise and

counterclockwise to find the highest idle speed.

2. Turn the low speed needle (L) ¼ turn

counterclockwise from the position of the highest idle

speed.

+ 1/4

To adjust the idle speed screw (T)

1. Start the product.
2. Turn the idle speed screw clockwise until the saw

chain starts to rotate.

3. Turn the idle speed screw counterclockwise until the

saw chain stops.

Note: The idle speed is correctly adjusted when the

engine runs correctly in all positions. The idle speed

must also be safely below the speed at which the saw

chain starts to rotate.

WARNING: If the saw chain does not stop

when you turn the idle speed screw, speak

to your servicing dealer. Do not use the

product until it is correctly adjusted.

To adjust the high speed needle (H)

CAUTION: To make sure that the

adjustment is correct, speak to your

servicing dealer who has access to a

tachometer. Do not override the

recommended maximum idle speed.

1. Start the product.

2. Operate the product at full throttle for approximately

10 seconds.

3. Turn the high speed needle (H) ¼ counterclockwise.
4. Operate the product at full throttle for approximately

10 seconds again and listen to the difference in the

idle speed.

5. Turn the high speed needle (H) ¼ counterclockwise.
6. Operate the product at full throttle for approximately

10 seconds again and listen to the difference in the

idle speed.

Note: You have operated the product at adjustments

of H=±0, H=+¼, H=+½ from the basic adjustments.

The engine has a different sound for each

adjustment.

7. Turn the high speed needle (H) clockwise until the

adjustments is correct and the product has the

correct sound.

Note: The high speed needle (H) is correctly

adjusted when the product 4-cycles a little at full

throttle. If the product "screams" the product is set

too lean, which can cause damage to the engine.

The product is set too rich if the product 4-cycles and

ejects smoke.

To examine if the carburetor is correctly

adjusted

• Make sure that the product has the correct

acceleration capacity.

• Make sure that the product 4-cycles a little at full

throttle.

• Make sure that the saw chain does not rotate at idle

speed.

• If the product is not easy to start or has less

acceleration capacity, adjust the low and high speed

needles.

CAUTION: Incorrect adjustments can

cause damage to the engine.

To replace a broken or worn starter

rope

1. Loosen the screws to the starter housing.

1064 - 001 - 31.01.2019

Содержание GZ2700T





















































































Результаты поиска

Содержание GZ2700T

Отзывы:

Похожие инструкции для GZ2700T

Бренды по названию

Популярные бренды

Zenoah GZ2700T, Руководство оператора

Результаты поиска

Содержание GZ2700T

Отзывы:

Похожие инструкции для GZ2700T

Бренды по названию

Популярные бренды