background image

G2501 / G2501 OPS
          

GB-18

12. Limited warranty

Should any failure occur on the product under normal 
operating conditions within the applicable warranty peri-
od, the failed part will be replaced or repaired free of 
charge by a ZENOAH authorized dealer.

WARRANTY PERIOD: 

Six (6) months after purchased 

by end-user subject to 12 months from produced month. 
(30 days if used for rental purpose)

THE PURCHASER SHALL BEAR COSTS OF TRANS-
PORTING  THE  UNIT  TO  AND  FROM  THE  ZENOAH 
DEALER. 

THE PURCHASER SHALL NOT BE CHARGED FOR DI-
AGNOSTIC LABOR WHICH LEADS TO THE DETERMI-
NATION THAT A WARRANTED PART IS DEFECTIVE, IF 
THE DIAGNOSTIC WORK IS PER FORMED AT THE 
ZENOAH DEALER.

THE PURCHASER OR OWNER IS RESPONSIBLE FOR 
THE PERFORMANCE OF THE REQUIRED MAINTE-
NANCE AS DEFINED BY THE MANUFACTURER IN THE 
OWNER/OPERATOR MANUAL.

ANY WARRANTED PART WHICH IS NOT SCHEDULED 
FOR REPLACEMENT AS REQUIRED MAINTENANCE, 
OR WHICH IS SCHEDULED ONLY FOR REGULAR IN-
SPECTION TO THE EFFECT OF REPAIR OR “REPLACE 
AS NECESSARY” SHALL BE WARRANTED FOR THE 
WARRANTY PERIOD. ANY WARRANTED PART WHICH 
IS SCHEDULED FOR REPLACEMENT AS REQUIRED 
MAINTENANCE SHALL BE WARRANTED FOR THE 
PERIOD OF TIME UP TO THE FIRST SCHEDULED RE-
PLACEMENT POINT FOR THE PART.

ANY REPLACEMENT PART THAT IS EQUIVALENT IN 
PERFORMANCE AND DULABILITY MAY BE USED IN 
NON-WARRANTY MAINTENANCE OR REPAIRS, AND 

SHALL NOT REDUCE THE WARRANTY OBLIGATION 
OF THE COMPANY.

THE COMPANY IS LIABLE FOR DAMAGES TO OTHER 
ENGINE COMPONENTS CAUSED BY THE FAILURE OF 
A WARRANTED PART STILL UNDER WARRANTY.

THE WARRANTY DOES NOT APPLY TO

 THOSE 

UNITS WHICH HAVE BEEN DAMAGED BY NEGLI-
GENCE OF INSTRUCTION LISTED IN THE OWNER/
OPERATOR MANUAL FOR PROPER USE AND MAIN-
TENANCE OF THE UNITS ACCIDENT MISHANDLING, 
ALTERATION, ABUSE, IMPROPER LUBRICATION, USE 
OF ANY PARTS OR ACCESSORIES OTHER THAN 
THOSE SPECIFIED BY THE COMPANY, OR OTHER 
CAUSES BEYOND THE COMPANY'S CONTROL.

THIS WARRANTY DOES NOT COVER

 THOSE PARTS 

REPLACED BY NORMAL WEAR OR HARMLESS 
CHANGES IN THEIR APPEARANCE.

THERE ARE NO OTHER EXPRESS WARRANTIES.

ANY IMPLIED WARRANTY 

is limited to the duration of the 

limited warranty. Otherwise, this limited warranty is in lieu of 
all other expressed or implied warranties, including any 

warranty of 

FITNESS FOR A PARTICULAR PURPOSE 

OR USE

 and any implied warranty 

MERCHANTABILITY

 

otherwise applicable to this product.

LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL 
DAMAGE UNDER ANY AND ALL WARRANTIES ARE 
EXCLUDED.

IF YOU NEED TO OBTAIN MORE INFORMATION, 
PLEASE CALL YOUR NEAREST SERVICE CENTER, OR 
C H E C K  P L E A S E  Z E N O A H  W E B  S I T E  h t t p : / /
www.zenoah.net

*01_G2501 G2501ops_GB_CS5_六.indd   18

16/09/21   16:49

Содержание G2501



















Отзывы: