background image

GB-2

EX2600

SAFETY FIRST

Instructions contained in warnings within this manual marked 
with a   symbol concern critical points which must be taken 
into consideration to prevent possible serious bodily injury, and 
for this reason you are requested to read all such instructions 
carefully and follow them without fail.

WARNINGS IN THE MANUAL

WARNING

This mark indicates instructions, which must be followed in or-
der to prevent accidents, which could lead to serious bodily in-
jury or death.

IMPORTANT

This mark indicates instructions, which must be followed, or it 
leads to mechanical failure, breakdown, or damage.

NOTE

This mark indicates hints or directions useful in the use of the 
product.

Contents

  1.  Parts location ....................................................3
  2. Specifications ....................................................4
  3.  Warning labels on the machine ........................5
  4.  Symbols on the machine ...................................5
  5.  For safe operation .............................................6
  6.  Set up ..............................................................10
  7.  Fuel and chain oil ............................................15
  8. Operation ........................................................16
  9. Maintenance ...................................................24
 10.  Storage ............................................................29
 11.  Disposal ..........................................................29
  12.  Troubleshooting guide ....................................30

 01-EX2600_GB_cs5_二.indd   2

17/04/14   18:09

Содержание EX2600































Отзывы: