background image

7

5. For safe operation

1. Read this manual carefully until you

completely understand and follow all safety
and operating instructions. 

2. Keep this manual handy so that you may refer

to it later whenever any questions arise. Also
note, if you have any questions which cannot
be answered herein, contact the dealer from
whom you purchased the product.

3. Always be sure to include this manual when

selling, lending, or otherwise transferring the
ownership of this product.

4. Never allow children or anyone unable to fully

understand the directions given in the manual
to use the machine.

WORKING CONDITION

1. When using the product, you should wear proper

clothing and protective equipment.

(1) Helmet
(2) Ear protectors
(3) Protection goggles or face protector
(4) Thick work gloves
(5) Non-slip-sole work boots

2. And you should carry with you.

(1) Attached tools and files
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working area (rope,

warning signs)

(5) Whistle (for collaboration or emergency)
(6) Hatchet or saw (for removal of obstacles)

3. Do not wear loose clothing, jewelry, short

trousers, sandals, or go barefoot. Do not wear
anything which might be caught by a moving
part of the unit. Secure hair so it is above
shoulder length. 

WORKING CIRCUMSTANCE

1. Never start the engine inside a closed room or

building. Exhaust gases contain dangerous
carbon monoxide. 

2. Never use the product,

a. when the ground is slippery or when you can’t

maintain a steady posture.

Содержание BCZ2400S





































Отзывы: