background image

 

 

 

 

Flat Sensato v2 

https://www.zennio.com

                                                                  

Technical Support:

 

https://support.zennio.com

 

 

   

 

12 

Figure 6.

 Notification LED 

– Green, Yellow and Red 

The parameters available in this tab are: 

 

Colours  Shown 

[

Green and Yellow/

Green, Yellow and Red

]: allows selecting 

whether the notification LED comprises two or three colours.  

 

Red / Yellow / Green

: humidity value (0-100%) from which the notification LED 

will  display  the  indicated  colour.  The  limit  values  (0%  and  100%)  are  not 

editable. Default values are shown in the following figures. 

Note:  The threshold values should be set from highest to lowest (from top to 

bottom).  If  this  indication  is  not  met,  default  values  will  be  taken.  In  addition, 

an  alert  message  will  be  shown:

 Incorrect  yellow  threshold  values.  The 

default values will be downloaded in case of an incorrect parameterisation.

  

The  notification  LED  can  be  enabled  or  disabled  at  any  time  by  means  of  the  binary 

object 

"[LED] Notification LED"

. Thus: 

 

  If  the  functionality  starts  enabled  after  programming,  the  LED  will  maintain 

the  configuration  set  by  parameter  against  enable/disable  actions  performed 

via the object.  

 

If  it  is  started  disabled,  the  object  will  allow  its  activation,  using  the  default 

colours and thresholds for notification. 

 

 

 

Содержание Flat Sensato v2





















Отзывы: