background image

3

Status display / Error codes

The symbols in the table below show the meter’s operational status. The status messages only appear 
in the main display (energy)! The temporary display of the warning triangle can be caused by special 
operating states and does not always mean that the device is malfunctioning. However, should the symbol 
be displayed over a longer period of time you should contact the service company.

Error codes show faults detected by multidata. If more than one error appears, the sum of the error 
codes is displayed: Error 1005 = error 1000 and error 5.
.

Symbol 

Status 

Event

 

Flow existent 

-

 

Attention! 

Check system / device for errors

 

Data transmission 

-

 

Emergency operation 

Exchange device

 

External power supply 

-

Code 

Error 

Event

Short-circuit return sensor 

Check sensors, replace if needed

Interruption return sensor  

Check sensors, replace if needed

Short-circuit supply sensor 

Check sensors, replace if needed

Interruption supply sensor 

Check sensors, replace if needed

Hardware error 

Exchange device

Battery empty or wrong temp. sensor  Check device / sensor

Temperatures out of measuring range  Correction heating system

100 

Emergency operation 

Exchange device

1000 

Battery life time exceeded 

Exchange device

2000 

Initial verification expired 

Exchange device

> 8000 

Internal hardware error 

Exchange device

Содержание 08765432













Отзывы: