Service Mode
7-8
206-3612 ZENITH PRO 1200X 151199
Highlight
'Projector Warm Up' by pushing the control disk up or down
and press ENTER
ENTER
ENTER
ENTER
ENTER to select the projector warm up menu.
The ON/OFF option can be toggled with the ENTER
ENTER
ENTER
ENTER
ENTER key.
Select with or
then <ENTER>
<EXIT> to return.
SERVICE MODE
SERVICE MODE
SERVICE MODE
SERVICE MODE
SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
PROJECTOR WARM UP
PROJECTOR WARM UP
PROJECTOR WARM UP
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
PROJECTOR WARM UP
PROJECTOR WARM UP
PROJECTOR WARM UP
PROJECTOR WARM UP
PROJECTOR WARM UP
OPTION : ON
A FULL WHITE PATTERN
WILL BE GENERATED FOR
20 MINUTES AT POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
TOGGLE OPTION ON OR OFF
with <ENTER>
<EXIT> to return
When in the ON position (and the CRT run in cycle is OFF), the projector
can start up with a warm up period of 20 minutes. During the start up
a warm up menu will displayed. This menu offers the possibility to skip
the warm up periode anyway by pressing the EXIT key and offers the
possibility to adjust the horizontal and vertical amplitude of the this white
image with the control disk. During this warm up period, a full white
image is shifted on the CRT faceplate to avoid a burn in.
Every 30 seconds a text box will be displayed on another place on the
screen with the remaining time to go.
When EXIT is pressed during this warm up periode, the warm up menu
will be redisplayed with the remaining time indication. Press another
time EXIT to interrupt the warm up cycle.
When the warm up option is OFF, when switching on the the projector,
it starts immediately with the projection of the selected source.
CRT Drive Mode
CRT Drive Mode
CRT Drive Mode
CRT Drive Mode
CRT Drive Mode
The projector CRT's can be driven with the normal current (normal
mode), a lower current (economic mode) or with a higher current (boost
mode).
To change the drive mode, highlight 'CRT drive mode' by pushing the
control disk up or down and press ENTER to display the CRT drive
mode menu.
To change the boost mode, push the control disk up or down to select
a display mode and press ENTER
ENTER
ENTER
ENTER
ENTER to select.
The following modes are available :
Select with or
then <ENTER>
<EXIT> to return.
SERVICE MODE
SERVICE MODE
SERVICE MODE
SERVICE MODE
SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
CRT DRIVE MODE
CRT DRIVE MODE
CRT DRIVE MODE
CRT DRIVE MODE
MORE...
CRT DRIVE MODE
CRT DRIVE MODE
CRT DRIVE MODE
CRT DRIVE MODE
CRT DRIVE MODE
NORMAL
ECONOMIC
TEMPORARY BOOST
PERMANENT BOOST
WARNING : permanent
boost mode reduces the lifetime
of the CRT's !
Select with or
then <ENTER>
<EXIT> to return.
- Normal
- Economic : lower drive current to the CRT's, the lifetime of the CRT's
will enlarge but the light output will reduce.
- Tempory boost : higher drive current to the CRT's, the lifetime of the
CRT's will shorten but the light output will be higher. This situation
is tempory, when restarting the projector, the drive mode is auto-
matically set to normal.
- Permanent boost : higher drive current to the CRT's, the lifetime of
the CRT's will shorten but the light output will be higher. This setting
will be saved in the EEPROM. When restarting the projector, it will
start up in boost mode.
A warning, permanent BOOST mode in use, will be displayed to inform
the user.
When text is on, this warning will be repeated every time a new source
is selected.
WARNING
WARNING
WARNING
WARNING
WARNING
PERMANENT
BOOST MODE
IN USE !
Содержание PRO1200X
Страница 1: ...PRO1200X OWNER S MANUAL ...
Страница 14: ...Connections 3 6 206 3612 ZENITH PRO 1200X 151199 ...