FACTORY MENU
3828VD0171G
2-8
DIGITAL FCS- FACTORY MENU
054-F SHPF0: Sharpness fo setting. 3= 3Mhz @
Normal mode
055-F BLKOFF: Blanking ON/OFF SW when AKBOFF=1
Default value is 0.
056-F CLPPHASE: Internal clamp phase pulse con-
trol. Default value is 0 (+5%).
057-F CLPSHIFT: Internal clamp pulse start phase
setting 1= Clamp phase setting –3.125%
058-F CLPGATE: Switch for gating internal clamp
pulse with input Hsync. 1=gated with inHsync.
059-F LEFTBLK
060-F RIGHTBLK
061-F HBLKSW: HBLK control enable for 4:3 soft-
ware full display mode on a 16:9 CRT. Default
value is 1.
062-F SABL: S-ABL gain setting. 3=S-ABL gain
max.
063-F SHPF1: High fo sharpness gain control.
Default value is 2.
064-F PREOVER Sharpness preshoot/overshoot ra-
tio setting. Range: 0-3, 0 = 1:1.5 (pre:over), 3
= 2:1 (pre:over). Default value is 0.
065-F VMLMT:
066-F VMDLY:
067-F AKBOFF:
068-F UPBLK
069-F LOBLK
070-F AFC_BOW: Vertical line bow adjustment.
Range: 0-63, Initial value: 31.
071-F AFC_ANGLE: Vertical line slope adjust-
ment. Range: 0-63, Initial value: 31.
072-F V_ASPECT: Aspect control ratio. Range:
0-63, Fixed Value: 47 for 4:3 CRT.
073-F V_SIZE: Vertical amplitude adjustment.
Range: 0-63, Initial value: 50.
074-F V_POSITION: Vertical position adjustment.
Range: 0-63, Initial value: 31.
075-F V_SCROLL: Vertical picture scroll con-
trol. Range: 0-63, Initial value: 28.
076-F V_LIN: Vertical linearity adjustment.
Range: 0- 15, Initial value: 07.
077-F V_S_CORRECTION: Vertical S correction.
Range: 0-15, Initial value: 5.
078-F UP_VLIN: Vertical linearity control. Range:
0- 15, Initial value: 0.
079-F LO_VLIN: Vertical linearity control. Range:
0- 15, Initial value: 0.
080-F H_SIZE: Horizontal amplitude adjustment.
Range: 0-63, Initial value: 43.
081-F H_POSITION: Horizontal position adjust-
ment. Range: 0-63, Initial value: 31.
082-F PIN_PHASE: Horizontal trapezoidal adjust-
ment. Range: 0-63, Initial value: 31.
083-F PIN_AMP: Pincushion adjustment. Range:
0-63, Initial value: 31.
084-F UP_CPIN: Horizontal pin adjustment for
top edge. Range: 0-63, Initial value: 38.
085-F LO_CPIN: Horizontal pin adjustment for
bottom edge. Range: 0-63, Initial value: 34.
086-F UP_UCP: Horizontal pin adjustment for ex-
treme top edge. Range: 0-3, Initial value: 0.
087-F LO_UCP: Horizontal pin adjustment for ex-
treme bottom edge. Range: 0-3, Initial value: 0.
088-F UP_UCG: Horizontal pin gain adjustment
for extreme top edge. Range: 0-3, Initial value:
0.
089-F LO_UCG: Horizontal pin gain adjustment
for extreme bottom edge. Range: 0-3, Initial
value: 0.
090-F UC_POL: Horizontal pin polarity setting
for extreme top & bottom edge. Range: 0-1, Ini-
tial value: 0.
091-F V_COMP: HV fluctuation compensation amount
setting for vertical picture size. Range: 0-15,
Initial value: 07.
092-F H_COMP: HV fluctuation compensation amount
setting for horizontal picture size.
Range: 0-15, Initial value: 07.
093-F PIN_COMP: HV fluctuation compensation
amount setting for horizontal pin distortion.
Range: 0-7, Initial value: 0.
