background image

2

COMPATIBILITY LIST

   

  The installation of the ZENEC system should be carried out by an authorized installer.

     Specific knowledge and tools are required to do the installation. Incorrect installation can cause  

 

  damage to the vehicle and the ZENEC system.
●  Correct functioning can only be guaranteed when you use the ZENEC original accessories included 

  in the kit or optionally available. The ZENEC system and the original accessories must under no 

  circumstance be modified or altered in any way. Inappropriate actions can cause damage to the 

  vehicle and the ZENEC system.

●  Torx screwdriver T25

●  Phillips screwdriver

●  Release tool made of plastic

●  Hand saw or equivalent

●  File

●  Hex key

●  Insulating tape

   

   

●  The target vehicle must factory configured with preinstallation for a radio. The ZENEC system is not  

  compatible with vehicles that are equipped with an OE radio or OE navigation system from the  

 factory.
●  This device installation manual applies to vehicle platforms appearing in the above compatibility list,      

  and in a condition as offered by the respective vehicle manufacturer. Other differing configurations  

  and installations of motorhome manufacturers are not considered in this installation manual. If  

  you have questions or vehicle-specific problems please contact the relevant motorhome  

 

 manufacturer.
●  The ZENEC system is equipped with an integrated DAB+ receiver. To make use of this you will need  

  a suitable DAB antenna (not included in kit) that must be connected to the ZENEC system.
●  If the target vehicle is equipped with a multifunction steering wheel, in order to support the steering  

  wheel remote functions a stalk interface accessory obtainable separately is required.  
●   Software updates to the ZENEC system are installed with a USB memory device.    

    Therefore when fitting the system make sure that the USB connection of the ZENEC system    

   will still be accessible later (installation of USB extension cable or USB hub).  
●  If you have questions or problems relating to the ZENEC system, please contact the dealer from  

  whom you purchased it. 

Model

Model Version

Model Year

FIAT Ducato III

250/251

2006 – 2011

FIAT Ducato III

250/251

2011 – 2014

FIAT Ducato III

250/251

from 2014

Citroën Jumper II 

250/250D/250L 

from 2006

Peugeot Boxer II 

250/251

from 2006

TOOLS REQUIRED

No. Article

Qty

1 ZENEC system

1

2 Mounting frame

1

3 Phillips screws

4

4 Remote control

2

5 microSD card with adapter

1

6 GPS antenna

1

7 Bluetooth microphone 

1

THE KIT INCLUDES

8 Antenna adapter ISO/DIN

1

9 Main connection cable 

10 USB extension cable

1

11 24-pin connection cable (4.2, Cam, MZone)

1

12 18-pin connection cable (Mic, Cam)

1

13 Connection cable parking brake

1

14 Metal plate for GPS antenna

1

15 Double-sided adhesive pad 

1

CAUTION

   

NOTE

Содержание Z-E3726







Отзывы: