59
ZVC385-001_v02
Disassembly/assembly of the “CYKLON”
dust container
The vacuum cleaner is equipped with a removable dust
container “CYKLON” in which dirt is accumulated. The dust
container “CYKLON” must be emptied once full.
1
Switch off the vacuum cleaner by pressing the “on/off”
button
(7)
and unplug the appliance.
2
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
3
Release the upper cover fastening
(12)
and open the
cover.
4
Remove the “CYKLON” dust container from the vacuum
cleaner chamber.
5
Pull aside the fastenings on the “CYKLON” dust
container and open the container. Empty the dirt from the
container.
After performing this activity, check the basic
EPA E10 filter and if necessary clean or replace
the filter.
6
Close the cover of the “CYKLON” dust container, firmly
press the fastenings until you hear a characteristic “click”.
The container must be tightly closed.
Otherwise the dust might enter the vacuum
cleaner chamber and the suction power will be
reduced.
7
Insert the empty “CYKLON” dust container into the
vacuum cleaner chamber.
8
Close the cover by pressing it until you hear
a characteristic click.
Filter disassembly
The vacuum cleaner is equipped with a filter element with
cyclone filtration which allows for vacuuming without the
traditional dust bag. A characteristic feature of the cyclone
filter is the use of the air stream whirl to separate solid dirt.
The separation of dirt takes place in the part of the container
with the circle cross section in which the whirling air pushes
the dirt on the wall of the container and next through an
opening to the adjacent chamber of the container. The
initially cleaned air is directed to the cone shaped EPA E10
filter which retains even the finest dirt fractions. The EPA E10
filter is equipped with a mesh protection which limits the
accumulation of dirt on the operating surface of the filter, due
to which the service life of the EPA E10 filter is longer.
The basic EPA washable class E10 filter is located at the
outlet of the cyclone filter container. The EPA E10 washable
filter is made of a special filtration material which enables to
rinse the filter under running water once it becomes dirty and
to reuse the filter.
An outlet EPA class E11 filter (nonwashable) is located at
the outlet of the vacuum cleaner.
E
Before changing the filters make sure that the vacuum
cleaner is switched off and unplugged from the mains supply.
BASIC EPA E10 FILTER
It is necessary to periodically clean the basic EPA E10 filer
from fine dust fractions.
Dismantle the “CYKLON” dust container and empty the
container according to the instructions in section
(E)
.
1
Turn the basic EPA EE10 filter in the UNLOCK direction
and remove the filter.
2
Remove the protective mesh of basic filter
(14)
.
●
Clean the mesh and dry it thoroughly. Replace the mesh
if damaged.
Due to safety reasons it is prohibited to install
a moist protective mesh.
●
Clean the pleats of the basic EPA E10 filter
(13)
. The
filter can be washed under running water. Thoroughly dry
the filter. In case of damage to the filter pleat, the filter
must be replaced with a new one.
Due to safety reasons it is prohibited to install
a moist or damaged basic EPA E10 filter (13).
3
After cleaning and drying the protective mesh and
the basic EPA E10 filter, install the protective mesh on the
EPA E10 filter and insert the whole unit to the “CYKLON”
dust container.
4
Press the interlock button and turn the basic EPA E10
filter
(13)
in the LOCK direction.
Insert the “CYKLON” dust container together with the
installed basic EPA E10 filter
(13)
into the vacuum cleaner
chamber and close the cover by pressing it until you hear
a characteristic “click” according to section
(E)
.
EPA E11 OUTLET FILTER
1
To replace the EPA E11 filter lift the vacuum cleaner
handle and open the accessory compartment.
2
Grab the filter cover by the fastening, firmly pull with the
thumb and lift it upwards.
3
Remove the EPA E11 filter case and replace it with a new
one. The EPA filter ensures an effective operation of the
vacuum cleaner for about 1 year.
4
Insert the cover so that the two protrusions in the lower
part of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
INLET FILTER
●
Release the upper cover fastening
(12)
and open the
cover.
●
Remove the SAFBAG dust bag module/the “CYKLON”
dust container from the vacuum cleaner chamber.
1
Slide the inlet filter casing with the installed inlet filter
from the tracks on the back side of the vacuum cleaner
chamber.
D
F
G
Содержание ZVC385SA
