Zelmer ZVC382ST, Инструкция по эксплуатации

Страница: 20 / 24

26
ZVC382-001_v01
–
The SAFBAG dust bag module – the dust is accumulated
in a disposable bag with high filtration quality.
1
Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2 Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device “A” and slide the tube into the hose handle so that
the locking device “A” is blocked in opening “B” .
3 Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/pull the tube
together.
4 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 You may assemble a basket for picking up small objects
in the combination brush with the small item separator.
In order to do so remove the blank cover and insert the
basket.
6 To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure .
7 The vacuum cleaner is equipped with an accessory
compartment. To open the compartment, lift the compartment
lid and pull it downwards.
8
Grab the plug (3) and pull the cord out of the vacuum
cleaner.
While pulling out the cord pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
9 Plug in the appliance.
Before operation make sure that the SAFBAG dust bag
module or the “CYKLON” dust container is installed in the
vacuum cleaner chamber and that all filters are installed in
the appliance.
10 Switch on the vacuum cleaner by pressing the “on/off”
button (7) .
11
The vacuum cleaner is equipped with an electronic power
control which allows to gradually adjust the vacuum cleaner
suction power during operation. To adjust the suction power
use the power adjustment buttons (11,9) – to increase the
suction power or – to decrease the suction power. The
suction power setting is indicated by the appropriate number
of lit diodes.
The vacuum cleaner will by default begin operation at the high
power. 4 diodes will light on the power level indicator (10) .
The suction power may be adjusted during operation. The
recommended settings are:
Setting 1 – vacuuming curtains
Setting 2 – vacuuming upholstery
Setting 3 – cost-effective power
Setting 4 – vacuuming carpets
Setting 5 – vacuuming hard floors and crevices.
12
Set the desired power value by pressing the power
adjustment buttons , (11,9) .
SAFBAG dust bag disassembly/assembly
C
1 The vacuum cleaner is equipped with a dust bag full
indicator (8) . When the dust bag full indicator (8) lights
during operation (with the nozzle or the brush lifted above
the cleaned surface) it means that the bag is full and needs
to be replaced. In addition the dust bag full indicator (8) may
activate if the suction hose or the elements attached to the
suction hose are clogged (suction power – level 5).
2 Switch off the vacuum cleaner by pressing the “on/off”
button (7) and unplug the appliance.
3 Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
4 Release the upper cover fastening (12) and open the cover.
5 Remove the SAFBAG dust bag module (21) from the
vacuum cleaner chamber
6 Grab the dust bag cover, gently bend it towards the
inside and remove the whole dust bag upwards.
7 Insert the plate of the new dust bag in the tracks of the
SAFBAG dust bag module (21) and slide it until stop. The
direction for inserting the dust bag is indicated by the arrow
on the bag.
8
Slide the SAFBAG dust bag module together with the
installed bag in the tracks located on the side of the vacuum
cleaner chamber. Close the cover by pressing it until you
hear a characteristic click – pay attention not to trap the
dust bag.
Do not vacuum without the SAFBAG dust bag
module/the “CYKLON” dust container installed
in the appliance. The lack of the SAFBAG dust
bag module/the “CYKLON” dust container
prevents from locking the upper cover of the
appliance.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
a) a)the SAFBAG dust bag /”CYKLON” dust container full
indicator will lit up,
b) the vacuum cleaner operates poorly,
c) the dust bag is full.
Disassembly/assembly of the “CYKLON”
dust container
The vacuum cleaner is equipped with a removable dust
container “CYKLON” in which dirt is accumulated. The dust
container “CYKLON” must be emptied once full.
1 Switch off the vacuum cleaner by pressing the “on/off”
button (7) and unplug the appliance.
2 Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
3 Release the upper cover fastening (12) and open the
cover.
E