Zelmer ZVC227SF, Руководство пользователя

Страница: 61 / 64

67
ZVC227-001_v01
THE CONE OF “CYCLONE” DUST CONTAINER
It is necessary to clean periodically the “CYCLONE” dust
container cone.
1
Disassembly “CYCLONE” dust container according to
point (C) .
2 Press the button located on “CYCLONE” dust container
and open the bottom of the container. If “CYCLONE dust
container is full, empty it according to the point (C) .
3
Turn the cone left, so the two tips located on the flange of
the cone were put out from the slots of the container. Put out
the cone.
4 If the “CYCLONE” dust container cone (15) is dirty, you
can rinse it with running water. Do not forget to dry above
mentioned cone before re-installation.
5
Insert the rinsed cone of “CYCLONE” dust container
into the container slot so the tip located on the flange of the
cone was in the slot of container’s body. Turn right the cone
so that the two tips located on the flange of the cone were
blocked in the slots of the container.
6 Snap the bottom of “CYCLONE” dust container. Please
pay attention to the proper positioning of seal found on the
bottom of the container.
7
Insert “CYCLONE” dust container to vacuum cleaner
chamber. The characteristic “click” indicates that the
container has been correctly mounted.
After-work procedures, cleaning, and
maintenance
1 Press the on/off button (4) to stop the vacuum cleaner.
2
Remove the plug of the cord from the socket.
3 Wind the cord by pressing the cord winder button (7) .
Hold the cord when doing it to avoid tangling the cord up or
letting the plug hit the vacuum cleaner.
4
Disconnect the telescopic suction pipe from the nozzle or
brush.
5 Disconnect the telescopic suction pipe from the hose.
6 Press the button situated on the end of the hose, and
remove the end of the hose from the inlet of the vacuum
cleaner.
7 The vacuum cleaner may be stored vertically or
horizontally. In order to do so, insert the fastening hook of
the combination brush to the combination brush fastener.
The hose may be attached to the vacuum cleaner, however
you have to make sure that it is not excessively bent during
storing.
8
If necessary, clean the casing and the chamber of the
vacuum cleaner with a damp cloth (it may be damped in
dishwashing liquid), dry it off, and wipe it dry.
Do not use any scrubbing agents or solvents.
F
G
The main function of the foam inlet filter (15) is to protect the
EPA E10 inlet filter (14) against excessive dirt.
For safety reasons it is unacceptable to install
a wet or damaged foam inlet filter (15).
●
Clean the pleats of the EPA E10 inlet filter (14) , and if
the filter is damaged, it should definitely be replaced with
a new one. If the EPA E10 inlet filter (14) is dirty, you may
replace it with a new one, clean it or rinse it with running
water. Before reinstalling the filter, make sure it is dry.
For safety reasons it is unacceptable to install
a wet or damaged EPA E10 inlet filter (14).
●
Situate the new/rinsed foam inlet filter in the previously
determined spot.
3 Place the new/rinsed EPA E10 inlet filter (14) in the
previously determined spot in the dust container.
4 Situate the CYKLON dust container with the installed
EPA E10 inlet filter (14) in the chamber of the vacuum
cleaner. A characteristic “click” signalizes the container has
been properly installed.
We advise you to replace the EPA E10 inlet
filter (14) with a new one every 6 months of use.
Do not use the vacuum cleaner without the EPA
E10 inlet filter (14) installed in the CYKLON
dust container. If the EPA E10 inlet filter is not
there, it is impossible to situate the CYKLON
dust container in the vacuum cleaner.
“MICROFILTER” OUTLET FILTER
1
In order to replace “Microfilter” outlet filter (18) press the
hook located in the filter cover and pull out the filter cover
from vacuum cleaner.
2 Pull out the “Microfilter” outlet filter (18) .
If the “Microfilter” outlet filter (18) is dirty, you can replace it with
a new filter, you can clean it or rinse with running water. Do not
forget to dry above mentioned filter before re-installation.
For safety reasons it is unacceptable to install
the moist or defective “Microfilter” outlet
filter (18).
3 Carefully insert a new / rinsed filter to previously
occupied space.
4 Put the filter cover so that two tips located at the right
side of the cover should hit the holes in the body of the
vacuum cleaner, press the filter cover so the hook snapped
in the body. Characteristic “click” sound informs, that the filter
cover has been properly installed.
Do not use the vacuum cleaner with no inlet
and outlet filters mounted in the device.
Damaged inlet and outlet filters must be always
replaced with new, factory original filters.
E