Zelmer ZSB1200 Series, Руководство пользователя

Страница: 35 / 38

37
32Z012-002_v04
●
Do not fill the jug over 1500 ml mark – in such case,
the content of the jug can lift the lid when the motor
starts up.
●
After 3 minutes operation stop the appliance for at
least minute to let the motor cool down. You can repeat
this cycle maximum10 times.
●
Do not operate when the jug is empty, as it can get
overheated.
●
The temperature of mixed ingredients should not
exceed 60°C.
9 Blender jug
10 Motor housing
11 Control panel
12 Anti-slip flange
13 Blocking ring
14 Blades
15 Gasket
Handling and operation
Preparation for operation
Before first usage (or after long storage) wash the jug (9) ,
lid (8) and feeder opening stopper (7) in hot water with
washing-up liquid, rinse and dry well. Keep your hands away
from cutting blades (14) – they are sharp.
Operation manual
1
Place the motor housing (10) on dry, firm, and horizontal
surface, near mains supply outlet and out of the reach of
children.
Arrange the supplying cord so that it does not
hang from the table or board and it can not be
pulled or dragged by accident.
2 Connect the plug into the mains supply outlet.
3
Place the jug (9) so, that the protrusions at the bottom
part of the jug (9) were fitted with the protrusions in top part
of motor housing (10) .
4 After proper assembling of the jug, the blue highlight
shall glow around the control panel (11) .
The handle of the blender jug (9) shall be
placed on the right side of the appliance.
5
Put the ingredients into the jug (9) .
6 Do not fill in over 1500 ml marked on the blender
jug (9) . In such case, the content of the jug can lift the lid
(8) when the motor starts up.
7 Before you use the stand blender, assemble the lid (8)
on the blender jug (9) so, that its protrusion was in line with
the protrusion in the jug.
Before you insert the lid (8) moisture the lid
gasket with water.
8 Insert the lid overlay (7) into the inlet in the lid (8) so that
the protrusions of the overlay enter the cuts in the lid inlet
and turn it left or right until it moves.
Do not start the stand blender without the
feeder opening stopper (7), especially, when
you use solid ingredients. They can be thrown
out of the opening.
9
Switch mixing on pressing speed I (2) , speed II (5) or
CLEAN/PULSE (6) .
B
Technical parameters
You can find the appliance technical data on the name plate.
Admissible time of non-stop operation: 3 minutes.
An interval between repeated operations: 10 minutes.
Maximum noise level: 80 dB/A.
The stand blender is built in II class of insulation .
It does not require connecting to mains supply socket with
earthing.
The stand blender meets the requirements of effective
standards.
The appliance meets the requirements of the following
directives:
–
Electrical equipment designed for use within specific
voltage limits (LVD) – 2006/95/EC.
–
Electro- Magnetic Compatibility (EMC) – 2004/108/EC.
The product is marked with symbol on the name plate.
For
marking declaration of conformity please visit the
manufacturer’s website at www.zelmer.com.
Appliance elements
1 Lid sieve
2 Speed I
3 ICE
4 ON/OFF
5 Speed II
6 CLEAN/PULSE
7 Feeder opening stopper
8 Lid
A
TIP
Product information and tips for
use
●
The stand blender is intended for domestic usage only.
In case it is used for gastronomic business purposes,
warrant y terms and conditions change.
●
During first start-up the appliances can emit some
odours. It is a normal phenomenon, which should be
over after a time.